Cisco Router IOS Upgrade Problem: Router Boots in Boot mode

Cisco Router IOS Upgrade Problem: Router Boots in Boot mode

Post by Ra » Sat, 14 Dec 2002 13:49:54



Have tried to upgrade the IOS of my cisco 1601 R router from 11.1 to
12 , successfully downloaded the IOS into router but , after that
every time router boots with boot mode attaching below is the config

Pls help

RAM Verma

*********************

System configuration has been modified. Save? [yes/no]: y
Building configuration...
[OK]
Proceed with reload? [confirm]

00:18:32: %SYS-5-RELOAD: Reload requested

System Bootstrap, Version 11.1(10)AA, EARLY DEPLOYMENT RELEASE
SOFTWARE (fc1)
Copyright (c) 1997 by cisco Systems, Inc.
C1600 processor with 2048 Kbytes of main memory

program load complete, entry point: 0x4018060, size: 0x1e1568

%QUICC_ETHER-1-LOSTCARR: Unit 0, lost carrier. Transceiver
problem?Flash boot: F
ile 'c1600-ny-l.112-17.p.bin' open failed.
boot of "cisco2-C1600" using boot helper
"eprom:c1600-boot-r.111-10.AA" failed
error returned: File boot failed -- File not accessible
loadprog: error - on file open
boot: cannot load "cisco2-C1600"

System Bootstrap, Version 11.1(10)AA, EARLY DEPLOYMENT RELEASE
SOFTWARE (fc1)
Copyright (c) 1997 by cisco Systems, Inc.
C1600 processor with 2048 Kbytes of main memory

*** BUS ERROR ***
access address = 0x2200000
program counter = 0x40011c0
status register = 0x2700
vbr at time of exception = 0x4000000
special status word = 0x022d
faulted cycle was a byte write

monitor: command "boot" aborted due to exception

System Bootstrap, Version 11.1(10)AA, EARLY DEPLOYMENT RELEASE
SOFTWARE (fc1)
Copyright (c) 1997 by cisco Systems, Inc.
C1600 processor with 2048 Kbytes of main memory

program load complete, entry point: 0x4018060, size: 0x1e1568

              Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706

Cisco Internetwork Operating System Software
IOS (tm) 1600 Software (C1600-BOOT-R), Version 11.1(10)AA, EARLY
DEPLOYMENT RELE
ASE SOFTWARE (fc1)
Copyright (c) 1986-1997 by cisco Systems, Inc.
Compiled Tue 18-Mar-97 14:01 by ccai
Image text-base: 0x04018060, data-base: 0x02005000

cisco 1601 (68360) processor (revision C) with 1536K/512K bytes of
memory.
Processor board ID 14226043
X.25 software, Version 2.0, NET2, BFE and GOSIP compliant.
1 Ethernet/IEEE 802.3 interface.
2 Serial(sync/async) network interfaces.
System/IO memory with parity disabled
8K bytes of non-volatile configuration memory.
4096K bytes of processor board PCMCIA flash (Read/Write)

Press RETURN to get started!

00:00:08: %QUICC_ETHER-1-LOSTCARR: Unit 0, lost carrier. Transceiver
problem?
00:00:08: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0,
changed sta
te to down
00:00:08: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0,
changed state
 to down
00:00:08: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1,
changed state
 to down
00:00:08: %LINK-3-UPDOWN: Interface Ethernet0, changed state to up
00:00:08: %LINK-3-UPDOWN: Interface Serial0, changed state to down
00:00:08: %LINK-3-UPDOWN: Interface Serial1, changed state to down
00:00:09: %SYS-5-CONFIG_I: Configured from memory by console
00:00:09: %SYS-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) 1600 Software (C1600-BOOT-R), Version 11.1(10)AA, EARLY
DEPLOYMENT RELE
ASE SOFTWARE (fc1)
Copyright (c) 1986-1997 by cisco Systems, Inc.
Compiled Tue 18-Mar-97 14:01 by ccai
JamesBP(boot)>

 
 
 

Cisco Router IOS Upgrade Problem: Router Boots in Boot mode

Post by Ra » Tue, 17 Dec 2002 23:56:33


Help .............................................................

> Have tried to upgrade the IOS of my cisco 1601 R router from 11.1 to
> 12 , successfully downloaded the IOS into router but , after that
> every time router boots with boot mode attaching below is the config

> Pls help

> RAM Verma

> *********************

> System configuration has been modified. Save? [yes/no]: y
> Building configuration...
> [OK]
> Proceed with reload? [confirm]

> 00:18:32: %SYS-5-RELOAD: Reload requested

> System Bootstrap, Version 11.1(10)AA, EARLY DEPLOYMENT RELEASE
> SOFTWARE (fc1)
> Copyright (c) 1997 by cisco Systems, Inc.
> C1600 processor with 2048 Kbytes of main memory

> program load complete, entry point: 0x4018060, size: 0x1e1568

> %QUICC_ETHER-1-LOSTCARR: Unit 0, lost carrier. Transceiver
> problem?Flash boot: F
> ile 'c1600-ny-l.112-17.p.bin' open failed.
> boot of "cisco2-C1600" using boot helper
> "eprom:c1600-boot-r.111-10.AA" failed
> error returned: File boot failed -- File not accessible
> loadprog: error - on file open
> boot: cannot load "cisco2-C1600"

> System Bootstrap, Version 11.1(10)AA, EARLY DEPLOYMENT RELEASE
> SOFTWARE (fc1)
> Copyright (c) 1997 by cisco Systems, Inc.
> C1600 processor with 2048 Kbytes of main memory

> *** BUS ERROR ***
> access address = 0x2200000
> program counter = 0x40011c0
> status register = 0x2700
> vbr at time of exception = 0x4000000
> special status word = 0x022d
> faulted cycle was a byte write

> monitor: command "boot" aborted due to exception

> System Bootstrap, Version 11.1(10)AA, EARLY DEPLOYMENT RELEASE
> SOFTWARE (fc1)
> Copyright (c) 1997 by cisco Systems, Inc.
> C1600 processor with 2048 Kbytes of main memory

> program load complete, entry point: 0x4018060, size: 0x1e1568

>               Restricted Rights Legend

> Use, duplication, or disclosure by the Government is
> subject to restrictions as set forth in subparagraph
> (c) of the Commercial Computer Software - Restricted
> Rights clause at FAR sec. 52.227-19 and subparagraph
> (c) (1) (ii) of the Rights in Technical Data and Computer
> Software clause at DFARS sec. 252.227-7013.

>            cisco Systems, Inc.
>            170 West Tasman Drive
>            San Jose, California 95134-1706

> Cisco Internetwork Operating System Software
> IOS (tm) 1600 Software (C1600-BOOT-R), Version 11.1(10)AA, EARLY
> DEPLOYMENT RELE
> ASE SOFTWARE (fc1)
> Copyright (c) 1986-1997 by cisco Systems, Inc.
> Compiled Tue 18-Mar-97 14:01 by ccai
> Image text-base: 0x04018060, data-base: 0x02005000

> cisco 1601 (68360) processor (revision C) with 1536K/512K bytes of
> memory.
> Processor board ID 14226043
> X.25 software, Version 2.0, NET2, BFE and GOSIP compliant.
> 1 Ethernet/IEEE 802.3 interface.
> 2 Serial(sync/async) network interfaces.
> System/IO memory with parity disabled
> 8K bytes of non-volatile configuration memory.
> 4096K bytes of processor board PCMCIA flash (Read/Write)

> Press RETURN to get started!

> 00:00:08: %QUICC_ETHER-1-LOSTCARR: Unit 0, lost carrier. Transceiver
> problem?
> 00:00:08: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0,
> changed sta
> te to down
> 00:00:08: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0,
> changed state
>  to down
> 00:00:08: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1,
> changed state
>  to down
> 00:00:08: %LINK-3-UPDOWN: Interface Ethernet0, changed state to up
> 00:00:08: %LINK-3-UPDOWN: Interface Serial0, changed state to down
> 00:00:08: %LINK-3-UPDOWN: Interface Serial1, changed state to down
> 00:00:09: %SYS-5-CONFIG_I: Configured from memory by console
> 00:00:09: %SYS-5-RESTART: System restarted --
> Cisco Internetwork Operating System Software
> IOS (tm) 1600 Software (C1600-BOOT-R), Version 11.1(10)AA, EARLY
> DEPLOYMENT RELE
> ASE SOFTWARE (fc1)
> Copyright (c) 1986-1997 by cisco Systems, Inc.
> Compiled Tue 18-Mar-97 14:01 by ccai
> JamesBP(boot)>


 
 
 

Cisco Router IOS Upgrade Problem: Router Boots in Boot mode

Post by Matt Hay » Wed, 18 Dec 2002 07:01:24



> Help .............................................................


> > Have tried to upgrade the IOS of my cisco 1601 R router from 11.1 to
> > 12 , successfully downloaded the IOS into router but , after that
> > every time router boots with boot mode attaching below is the config

> > Pls help

> > RAM Verma

> > *********************

> > System configuration has been modified. Save? [yes/no]: y
> > Building configuration...
> > [OK]
> > Proceed with reload? [confirm]

> > 00:18:32: %SYS-5-RELOAD: Reload requested

> > System Bootstrap, Version 11.1(10)AA, EARLY DEPLOYMENT RELEASE
> > SOFTWARE (fc1)
> > Copyright (c) 1997 by cisco Systems, Inc.
> > C1600 processor with 2048 Kbytes of main memory

> > program load complete, entry point: 0x4018060, size: 0x1e1568

> > %QUICC_ETHER-1-LOSTCARR: Unit 0, lost carrier. Transceiver
> > problem?Flash boot: F
> > ile 'c1600-ny-l.112-17.p.bin' open failed.
> > boot of "cisco2-C1600" using boot helper
> > "eprom:c1600-boot-r.111-10.AA" failed
> > error returned: File boot failed -- File not accessible
> > loadprog: error - on file open
> > boot: cannot load "cisco2-C1600"

> > System Bootstrap, Version 11.1(10)AA, EARLY DEPLOYMENT RELEASE
> > SOFTWARE (fc1)
> > Copyright (c) 1997 by cisco Systems, Inc.
> > C1600 processor with 2048 Kbytes of main memory

> > *** BUS ERROR ***
> > access address = 0x2200000
> > program counter = 0x40011c0
> > status register = 0x2700
> > vbr at time of exception = 0x4000000
> > special status word = 0x022d
> > faulted cycle was a byte write

> > monitor: command "boot" aborted due to exception

> > System Bootstrap, Version 11.1(10)AA, EARLY DEPLOYMENT RELEASE
> > SOFTWARE (fc1)
> > Copyright (c) 1997 by cisco Systems, Inc.
> > C1600 processor with 2048 Kbytes of main memory

> > program load complete, entry point: 0x4018060, size: 0x1e1568

> >               Restricted Rights Legend

> > Use, duplication, or disclosure by the Government is
> > subject to restrictions as set forth in subparagraph
> > (c) of the Commercial Computer Software - Restricted
> > Rights clause at FAR sec. 52.227-19 and subparagraph
> > (c) (1) (ii) of the Rights in Technical Data and Computer
> > Software clause at DFARS sec. 252.227-7013.

> >            cisco Systems, Inc.
> >            170 West Tasman Drive
> >            San Jose, California 95134-1706

> > Cisco Internetwork Operating System Software
> > IOS (tm) 1600 Software (C1600-BOOT-R), Version 11.1(10)AA, EARLY
> > DEPLOYMENT RELE
> > ASE SOFTWARE (fc1)
> > Copyright (c) 1986-1997 by cisco Systems, Inc.
> > Compiled Tue 18-Mar-97 14:01 by ccai
> > Image text-base: 0x04018060, data-base: 0x02005000

> > cisco 1601 (68360) processor (revision C) with 1536K/512K bytes of
> > memory.
> > Processor board ID 14226043
> > X.25 software, Version 2.0, NET2, BFE and GOSIP compliant.
> > 1 Ethernet/IEEE 802.3 interface.
> > 2 Serial(sync/async) network interfaces.
> > System/IO memory with parity disabled
> > 8K bytes of non-volatile configuration memory.
> > 4096K bytes of processor board PCMCIA flash (Read/Write)

> > Press RETURN to get started!

> > 00:00:08: %QUICC_ETHER-1-LOSTCARR: Unit 0, lost carrier. Transceiver
> > problem?
> > 00:00:08: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0,
> > changed sta
> > te to down
> > 00:00:08: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0,
> > changed state
> >  to down
> > 00:00:08: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1,
> > changed state
> >  to down
> > 00:00:08: %LINK-3-UPDOWN: Interface Ethernet0, changed state to up
> > 00:00:08: %LINK-3-UPDOWN: Interface Serial0, changed state to down
> > 00:00:08: %LINK-3-UPDOWN: Interface Serial1, changed state to down
> > 00:00:09: %SYS-5-CONFIG_I: Configured from memory by console
> > 00:00:09: %SYS-5-RESTART: System restarted --
> > Cisco Internetwork Operating System Software
> > IOS (tm) 1600 Software (C1600-BOOT-R), Version 11.1(10)AA, EARLY
> > DEPLOYMENT RELE
> > ASE SOFTWARE (fc1)
> > Copyright (c) 1986-1997 by cisco Systems, Inc.
> > Compiled Tue 18-Mar-97 14:01 by ccai
> > JamesBP(boot)>

Before you question the intelligence of this newsgroup, first question
to you, did you read the directions?
 
 
 

1. Booting Router IOS via another Router

Guys,

I need to boot RouterA via RouterB to get it's IOS. I know how to setup the
RouterB for a TFTP etc.
What commands/Config reg sets do I need on the Router that needs the IOS.

Many thanks
Pete

--
Get Paid every time you Surf the Web! Check out
http://www.alladvantage.com/go.asp?refid=BML-255

2. bug in dossrv need help...

3. Problem with router booting into ROM Mode

4. VAXstation II, what to do?

5. boot into router(boot)>

6. NPRINT on '95/32 client can't find Print Queue

7. Booting - my router is booting over and over

8. Even FTP Voyager Won't Delete Directories.

9. Looking for boot roms code and upgrade help for a Cisco 2501 router

10. Router boot modes

11. "Router(boot)>" mode suddently appear ????

12. Router booting in rom monitor mode