Looking for VME PPC Boards

Looking for VME PPC Boards

Post by Steve O'Neil » Thu, 29 May 1997 04:00:00



I'm looking for 6U VME PowerPC boards.  Preferably with serial and
ethernet interfaces and two PMC slots.  Any pointers would be
appreciated.

TIA.

Steve O'Neill

(603) 885-9765

 
 
 

Looking for VME PPC Boards

Post by Bill Denn » Sat, 31 May 1997 04:00:00




> I'm looking for 6U VME PowerPC boards.  Preferably with serial
> and ethernet interfaces and two PMC slots.  Any pointers would
> be appreciated.

see http://www.mot.com/computer



Technical Sales Support    (703) 714-0707            |    and they is us ...
Motorola Computer Group    (703) 714-0714 FAX        |              Pogo

 
 
 

Looking for VME PPC Boards

Post by Iain Tebbut » Sun, 01 Jun 1997 04:00:00




>I'm looking for 6U VME PowerPC boards.  Preferably with serial and
>ethernet interfaces and two PMC slots.  Any pointers would be
>appreciated.

>TIA.

>Steve O'Neill

>(603) 885-9765

I know Motorola have a number of boards but there are also some good
boards from Force and CES (Creative Electronic Systems in Switzerland).
I have a feeling that these boards are very similar? I did some VxWorks
work on the CES board last year and it seemed to perform very well.

If you need their number then email me and I'll get it for you.

Iain

--
       Iain Teb*
       Claritech Ltd
Tel:   +44 (0)1530 412488
Fax:   +44 (0)1530 412488

www:   http://www.veryComputer.com/

 
 
 

1. looking for VME period measurement board

The following is an instrumentation question.  I am looking for a VME board
that:

  1) provides period measurement capability for a minimum of two incoming
     analog channels

  2) uses at a minimum, a 2.5 MHz clock

  3) uses a 32-bit count register

  4) provides continuous period measurement

  5) provides the last gated count value for the previous period on a
     32-bit register (or 2 16-bit registers), which can be read without
     any delay, and completely asynchronously to the current period
     measurement process

  6) after initial setup from the host system, the only interaction needed
     is to read the last gated period using dumb simple programmed i/o --
     i.e. I don't want to have to say:

       a) start sampling on chnl 0
       b) spin or wait for interrupt while command is ack'ed
       c) spin or wait for interrupt while current period is being measured
       d) etc...

My operating range is 1 - 2500 Hz, with a +/- 0.1% resolution.
If anyone has any information on an interface that would meet these
requirements, please forward it to me at my address below.

Thank you very much.

Dean W. Anneser                  Pratt & Whitney Aircraft         \__ -\
Computer System Specialist       m.s. 161-05               Ooo.. (_)-V/( )
(203)565-9372 (desk) 5016 (fax)  400 Main St.               Live to Ride  
Uucp:     uunet!pwa-b!anneser    East Hartford, CT  06108  

"One test result is worth one thousand expert opinions" -- Wernher Von Braun

--
Dean W. Anneser                  Pratt & Whitney Aircraft         \__ -\
Computer System Specialist       m.s. 161-05               Ooo.. (_)-V/( )
(203)565-9372 (desk) 5016 (fax)  400 Main St.               Live to Ride  
Uucp:     uunet!pwa-b!anneser    East Hartford, CT  06108  

"One test result is worth one thousand expert opinions" -- Wernher Von Braun

2. LN32 - became GENICOM microLaser 320 ???

3. looking for a few good RISC VME boards

4. Win95 modem driver

5. First? or Last?

6. Artesyn PM/PPC boards available

7. Logging of when server is serving

8. Need source for a PPC, ethernet, ramed standalone board

9. looking for 386 and ppc distribs

10. FS: FORCE Pentura CPCI and VME PowerPC boards