IPE30 Error Msg

IPE30 Error Msg

Post by Gus Hampto » Mon, 23 Jun 2003 14:00:37



Hello Everyone,
I really need help here.  I'm working on a project for the PTA and now
this......

I've installed Photo Express 3.0 SE. No problem! When I click on the icon it
says "lpe30" "This program has performed an illegal operation and will be
shut down." In the "details section it reads as follows:

IPE30 caused an invalid page fault in
module KERNEL32.DLL at 015f:bff711be.
Registers:
EAX=81850000 CS=015f EIP=bff711be EFLGS=00010246
EBX=00000000 SS=0167 ESP=83362ca4 EBP=83362cb0
ECX=ffffffff DS=0167 ESI=00000000 FS=12ef
EDX=818573a8 ES=0167 EDI=6b556d61 GS=0000
Bytes at CS:EIP:
f2 ae f7 d1 8b 75 0c 8b 7d 08 8b c7 fc 51 c1 e9
Stack dump:
8185f738 00000000 83362dd4 83362ee4 bff7e6ef 83362dd4 6b556d61 8185f738
8185f74c 00000000 bff7e840 81877614 8182d94a 81878ae8 81878afc 00000003

Then I click to get rid of the error message and another one pops up and is
titled "Restriction" and goes on to say:

"This operation has been cancelled due to restriction in effect on this
computer. Please contact your system administrator."

I am the only person who uses this computer. Any ideas?

--
Gus Hampton

To email me remove "nospam" from email address.

 
 
 

IPE30 Error Msg

Post by Jerry Jon » Wed, 25 Jun 2003 01:58:05


It would seem your installation of PhotoExpress was not successful.

Have you tried uninstalling and the re-installing the software?

Jerry Jones
http://www.jonesgroup.net

 
 
 

1. DJPEG question about error msg.

Maybe someone on this list can explain the errors I have been getting.
I have been using the program DJPEG (comes with CJPEG) to convert files
from jpeg to ppm.  I'm using it via system calls from a program that is
cycling through many images.  It works fine for quite a while, then
after I leave and come back hours later, it will have crashed because
DJPEG refuses to convert any more images.  Here is the error it gives:

"DPMI: Not enough selectors."

The master program calls it again on another image, and this error is
given:

"CPU must be in REAL mode (not V86 mode) to run this program without
VCPI.  If you are using an EMS emulator, make sure the EMS isn't
disabled."

Any ideas here?  I am running this in a win 95 DOS box, and the code
being run is code compiled by DJGPP, the PC version of GCC.  The DOS box
does not have EMS disabled (under properties).  Oh yeah, the other thing
that happens is a win95 dialog pops up saying that the program may not
run well unless it is run in MS-DOS mode.  "Would you like to create a
shortcut to this program that will run it in MS-DOS mode?"  This throws
me a little, since I'd really prefer to just do this work in a DOS
window without having to double click win95 icons all the time.

Thanks for any help you can provide...

Charles McDowell

2. NOVELIST NEEDS AN IMAGE!!!

3. Q: XView error msg

4. Camera Control Using Mouse?

5. Error Msg When closing PSP

6. Ho to change the printer resolution

7. Surfaces Panel Error msg: Can't open surface file

8. Help! Dialog.com database about graphics!

9. DXF import error msg

10. HELP-ERROR MSG ERCORE.DLL ON LW 3D

11. error msg while using 'fit'

12. I get a very strange error msg :