Apple CD150 (Sony CDU-8002) problem with NetBSD-1.5.3/mac68k on MacIIcx

Apple CD150 (Sony CDU-8002) problem with NetBSD-1.5.3/mac68k on MacIIcx

Post by IKEDA Shiger » Sat, 31 Aug 2002 21:08:20



-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

Hi,

I upgraded NetBSD/mac68k on my Macintosh IIcx.  I tried to mount CDROM,
But the following error occurs and can't mount.

sbc0: too much data padding
sbc0: aborting, but phase=DATA_IN (reset)
sbc0: reset SCSI bus for TID=2 LUN=0
sbc0: too much data padding
sbc0: aborting, but phase=DATA_IN (reset)
sbc0: reset SCSI bus for TID=2 LUN=0

I believe I could use this CDROM drive with NetBSD-1.4.x.
And works fine with my PowerBook 145B and MacOS7.5.5 on this MacIIcx.

My SCSI hard disk will corrupt if I use generic SCSI driver so I've been
using SBC (PDMA) driver.

Any info are welcome.  TIA.

Here is dmesg of GENERICSBC kernel:

[ preserving 419473 bytes of netbsd a.out symbol table ]
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 1.5.3 (GENERICSBC) #3: Tue Jul  2 07:49:25 CST 2002

Apple Macintosh IIcx  (68030)
cpu: delay factor 166
total memory = 32768 KB
avail memory = 26592 KB
using 435 buffers containing 1740 KB of memory
mrg: 'Mac II class ROMs' ROM glue, tracing off, debug off, silent traps
mrg: I/O map kludge for ROMs that use hardware addresses directly.
mainbus0 (root)
obio0 at mainbus0
adb0 at obio0
asc0 at obio0: Apple Sound Chip
iwm0 at obio0: Apple GCR floppy disk controller
sbc0 at obio0: options=1<PDMA>
scsibus0 at sbc0: 8 targets, 8 luns per target
zsc0 at obio0 chip type 0
zsc0 channel 0: d_speed   9600 DCD clk 0 CTS clk 0
zstty0 at zsc0 channel 0
zsc0 channel 1: d_speed   9600 DCD clk 0 CTS clk 0
zstty1 at zsc0 channel 1
nubus0 at mainbus0
macvid0 at nubus0 slot 9: Vimage by Interware Co., Ltd.
macvid0: 640 x 480, monochrome
macfb0 at macvid0
wsdisplay0 at macfb0: console (std, vt100 emulation)
ae0 at nubus0 slot a: MacCon Ethernet, 32KB memory
ae0: Ethernet address 00:00:94:61:3f:bf
fpu0 at mainbus0 (mc68882)
ae0: length does not match next packet pointer
ae0: len 0000 nlen ff00 start 12 first 00 curr 11 next 00 stop 80
ae0: NIC memory corrupt - invalid packet length 65280
adb0 (direct, II series): 2 targets
aed0 at adb0 addr 0: ADB Event device
akbd0 at adb0 addr 2: keyboard II (Japanese layout)
wskbd0 at akbd0: console keyboard, using wsdisplay0
ams0 at adb0 addr 3: 1-button, 100 dpi mouse
wsmouse0 at ams0
scsibus0: waiting 2 seconds for devices to settle...
sd0 at scsibus0 target 0 lun 0: <FUJITSU, M1606S-512, 6237> SCSI2 0/direct fixed
sd0: 1041 MB, 3457 cyl, 6 head, 102 sec, 512 bytes/sect x 2131992 sectors
cd0 at scsibus0 target 2 lun 0: <SONY, CD-ROM CDU-8002, 1.8g> SCSI1 5/cdrom remo
vable
boot device: sd0
root on sd0a dumps on sd0b
PRAM: 0x3d6f5d28, macos_boottime: 0x3d6f5d0c.
root file system type: ffs
sbc0: too much data padding
sbc0: aborting, but phase=DATA_IN (reset)
sbc0: reset SCSI bus for TID=2 LUN=0
sbc0: too much data padding
sbc0: aborting, but phase=DATA_IN (reset)
sbc0: reset SCSI bus for TID=2 LUN=0
#

-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.0.7 (OpenBSD)
Comment: no comments

iD8DBQE9b2AhUHt8kCIJ1VoRAvMJAKCus3lGsDBwVp5B/RSElVvC/DoIRwCfW3P9
p/t4XT7e45lyJ06JOYAoAeY=
=aOFR
-----END PGP SIGNATURE-----

 
 
 

Apple CD150 (Sony CDU-8002) problem with NetBSD-1.5.3/mac68k on MacIIcx

Post by IKEDA Shiger » Sat, 31 Aug 2002 21:42:50


-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

Hi,

I've just upgraded NetBSD/mac68k on my Macintosh IIcx.  When I tried to
mount CDROM, the following error occurs and can't mount.

sbc0: too much data padding
sbc0: aborting, but phase=DATA_IN (reset)
sbc0: reset SCSI bus for TID=2 LUN=0
sbc0: too much data padding
sbc0: aborting, but phase=DATA_IN (reset)
sbc0: reset SCSI bus for TID=2 LUN=0

I believe I could use this CDROM drive with NetBSD-1.4.x.
And works fine with my PowerBook 145B and MacOS7.5.5 on this MacIIcx.

My SCSI hard disk will corrupt if I use generic SCSI driver so I've been
using SBC (PDMA) driver.

Any info are welcome.  TIA.

Here is dmesg of GENERICSBC kernel:

[ preserving 419473 bytes of netbsd a.out symbol table ]
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 1.5.3 (GENERICSBC) #3: Tue Jul  2 07:49:25 CST 2002

Apple Macintosh IIcx  (68030)
cpu: delay factor 166
total memory = 32768 KB
avail memory = 26592 KB
using 435 buffers containing 1740 KB of memory
mrg: 'Mac II class ROMs' ROM glue, tracing off, debug off, silent traps
mrg: I/O map kludge for ROMs that use hardware addresses directly.
mainbus0 (root)
obio0 at mainbus0
adb0 at obio0
asc0 at obio0: Apple Sound Chip
iwm0 at obio0: Apple GCR floppy disk controller
sbc0 at obio0: options=1<PDMA>
scsibus0 at sbc0: 8 targets, 8 luns per target
zsc0 at obio0 chip type 0
zsc0 channel 0: d_speed   9600 DCD clk 0 CTS clk 0
zstty0 at zsc0 channel 0
zsc0 channel 1: d_speed   9600 DCD clk 0 CTS clk 0
zstty1 at zsc0 channel 1
nubus0 at mainbus0
macvid0 at nubus0 slot 9: Vimage by Interware Co., Ltd.
macvid0: 640 x 480, monochrome
macfb0 at macvid0
wsdisplay0 at macfb0: console (std, vt100 emulation)
ae0 at nubus0 slot a: MacCon Ethernet, 32KB memory
ae0: Ethernet address 00:00:94:61:3f:bf
fpu0 at mainbus0 (mc68882)
ae0: length does not match next packet pointer
ae0: len 0000 nlen ff00 start 12 first 00 curr 11 next 00 stop 80
ae0: NIC memory corrupt - invalid packet length 65280
adb0 (direct, II series): 2 targets
aed0 at adb0 addr 0: ADB Event device
akbd0 at adb0 addr 2: keyboard II (Japanese layout)
wskbd0 at akbd0: console keyboard, using wsdisplay0
ams0 at adb0 addr 3: 1-button, 100 dpi mouse
wsmouse0 at ams0
scsibus0: waiting 2 seconds for devices to settle...
sd0 at scsibus0 target 0 lun 0: <FUJITSU, M1606S-512, 6237> SCSI2 0/direct fixed
sd0: 1041 MB, 3457 cyl, 6 head, 102 sec, 512 bytes/sect x 2131992 sectors
cd0 at scsibus0 target 2 lun 0: <SONY, CD-ROM CDU-8002, 1.8g> SCSI1 5/cdrom remo
vable
boot device: sd0
root on sd0a dumps on sd0b
PRAM: 0x3d6f5d28, macos_boottime: 0x3d6f5d0c.
root file system type: ffs
sbc0: too much data padding
sbc0: aborting, but phase=DATA_IN (reset)
sbc0: reset SCSI bus for TID=2 LUN=0
sbc0: too much data padding
sbc0: aborting, but phase=DATA_IN (reset)
sbc0: reset SCSI bus for TID=2 LUN=0
#

-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.0.7 (OpenBSD)
Comment: no comments

iD8DBQE9b2gmUHt8kCIJ1VoRAtMrAKCQ+xdxQ7CYkbOcOnm2Iv+z9cczUgCfcddw
iYV8tVkDmb/Gpw7Tfpbl1HQ=
=mvtI
-----END PGP SIGNATURE-----

 
 
 

1. Sony CDU-33A = =CDU-31A?

I ordered a CDU31A (knowing that there are OS/2 and linux
drivers for it). I recieved a CDU33A instead. I am glad, it is a
double speed drive, but...

I tried OS/2 with the 31A drivers and it seems to run without
any noticable problems till now.

I don't yet have linux installed, but I am wondering...will it work
with the 31A drivers, or have 33A drivers been written?
I checked the hardware faq (version 0.6 dated Aug 93) and
that mentions drivers for the 31A but not 33A. I looked in the
LSM of December 13, and it mentions neither the 31A nor the
33A. (Why is the 31A driver not mentioned?)

I have not yet used linux, so I am just feeling my way around
the FAQ's and the HOWTO's. If anybody can help I could use
it. I do not subscribe to the comp.os.linux.* groups, so
please copy all replies to email as well. Thanx

2. DOSEMU 0.60.1 / patch for Windows 3.1

3. problem booting NetBSD/mac68k

4. Dial-in server blues....

5. NetBSD/mac68k 1.1 misc problems

6. bttv and v4l2 driver

7. Problems with video card and NetBSD/mac68k

8. make: Fatal error: Command failed for target `libXpm.so.4.3'

9. NetBSD/Mac68k installer problem

10. Sounds, color X and mozilla problems, NetBSD 1.3.2/mac68k/Centris 660av

11. NetBSD on mac68k Problems installing ports

12. Video problem with Mac IIcx and NetBSD Mac68K v1.1

13. SunOS 5.3 (Solaris 5.3) Patch Report