problem running xv and others in linux .99pl4 (SLS 1.0)

problem running xv and others in linux .99pl4 (SLS 1.0)

Post by MATTHEW S CROCK » Sun, 14 Feb 1993 03:09:33



I've been having problems running binaries I get from sunsite and
tsx-11 ftp the file and dl to my linux box.  uncompress and tar -xf
work fine and I get the binaries.  However when I try to run tye
binary I get command not found.  This has happend to xv-486binaries,
xtrek, xloadimage, xview ...   what am I doing wrong. I do have the
486-libs but I might not have installed them correctly.

Another ??  I just got ingres-##???.TZ from sunsite but lharc dumps
core with a seg fault on /primer/operator.c (I think thats the file)
everything else up to that point go fine.. is the lhz file corrupted?

other than those two ??'s everything is great ;)

-Matt
--
- Matthew S. Crocker             Crocker Communication Center

                                 Greenfield, MA 01302-0714

 
 
 

problem running xv and others in linux .99pl4 (SLS 1.0)

Post by srb.. » Tue, 16 Feb 1993 19:49:42


I`ve tried to adapt the file Xconfig to my Monitor, but the only thing I get
is snow on the screen. Who can help me ? Here are the datas you may need:

800x600 :
horizontal-frequency : 35.2  MHz
display-time        : 22.22 us
pre-sync            :  0.67 us
sync                :  2.00 us
post-sync           :  3.56 us

vertical-frequency  : 56.2  MHz
display-time        : 17.07 ms
pre-sync            :  0.03 ms
sync                :  0.06 ms
post-sync           :  0.6  ms

1024x768 interlaced :
horizontal-frequency : 35.52 MHz
display-time        : 22.8  us
pre-sync            :  0.18 us
sync                :  3.92 us
post-sync           :  1.25 us

vertical-frequency  : 87 MHz
display-time        : 10.81 ms
pre-sync            :  0.014 ms
sync                :  0.113 ms
post-sync           :  0.563 ms

The Monitor is an M55-colour.

 
 
 

problem running xv and others in linux .99pl4 (SLS 1.0)

Post by Joseph R. Pann » Wed, 17 Feb 1993 05:36:42



>horizontal-frequency : 35.2  MHz
> ...
>vertical-frequency  : 56.2  MHz
....>
>horizontal-frequency : 35.52 MHz
> ...
>vertical-frequency  : 87 MHz

You must be pulling our collective leg here!  Have you considered that
frequency might come in other units besides MHz?

Joe Pannon

 
 
 

problem running xv and others in linux .99pl4 (SLS 1.0)

Post by Markus Wenz » Tue, 23 Feb 1993 17:27:15



Quote:>I've been having problems running binaries I get from sunsite and
>tsx-11 ftp the file and dl to my linux box.  uncompress and tar -xf
>work fine and I get the binaries.  However when I try to run tye
>binary I get command not found.  This has happend to xv-486binaries,
>xtrek, xloadimage, xview ...   what am I doing wrong. I do have the
>486-libs but I might not have installed them correctly.

If you are using tcsh, you should perform a 'rehash' after installing
new binaries in order to rescan the path.

Regards, Markus.

--
/dev              Markus Wenzel, University of Stuttgart

~/.ircrc/nick     Marsu
/etc/motd         'Linux' is no trademark of AT&T.

 
 
 

1. SLS ver 0.99pl4 wont let me login!

Hi all,

        I'm having trouble with SLS booting all the way. I get as far
as..

--------------- begin ------------

Loading 624640 bytes into ram disk
.......................................
done

---------------  end  ------------
(Not sure exactly what it says but close to the above)

..and that is as far as I get. I can change between VC's and what I type
is displayed but no login. I haven't had Internet access since linux 0.12
but I was happily using it so it didn't matter. Does anyone know what
the problem might be. I have SLS ver. 0.99pl4. (quite the jump from 0.12
to 0.99pl4!) My system is a 486DX, 2mb ram.

Please respond by news. I am using a friends account and do not have access
to mail!

                                Thanks in advance,
                                Shawn

2. pb with 1.2.13

3. Anyone run/build lucid emacs (lemacs) with 99pl4?

4. Latex installation on SUSE 7.0

5. SLS 1.0 (1.01?) shared libraries problem.

6. [PATCH] linux-2.5.34_vsyscall_A0

7. can't run Xfree from SLS on NEC Ultralite SL/25C

8. what does an admin do ? WinGuru on doing your job properly

9. SLS 1.0[12] install problem/weirdness/bug

10. binaries wanted for NetBSD 1.0: xv xpaint pdksh pgp2.6

11. Can't run term2.04 remote on Linux 1.0

12. Radeon VE and XFree86-4.1.0: compiled OK but problem running

13. SLS 1.0 --> 1.02 Upgrade?