hi,
hopefully someone could help me.
i was wondering if i could turn off the "sendmail" daemon in the command mode??
thanks.
by David K » Thu, 12 Dec 2002 04:06:13
hopefully someone could help me.
i was wondering if i could turn off the "sendmail" daemon in the command mode??
thanks.
by Bit Twiste » Thu, 12 Dec 2002 04:30:24
man chkconfigQuote:> i was wondering if i could turn off the "sendmail" daemon in the command mode??
by David M. Sync » Mon, 16 Dec 2002 10:46:59
> hopefully someone could help me.
> i was wondering if i could turn off the "sendmail" daemon in the command mode??
> thanks.
by Avedi » Mon, 16 Dec 2002 13:29:45
to stop it now, "service sendmail stop"
~Av
On Sun, 15 Dec 2002 01:46:59 GMT, "David M. Synck"
>> hopefully someone could help me.
>> i was wondering if i could turn off the "sendmail" daemon in the command mode??
>> thanks.
>Yes, you can. The syntax is "chkconfig --level # service on|off|restart
>So if you wanted to turn off sendmail for both runlevels 3 and 5, you
>would type the following "chkconfig --level 35 sendmail off". I believe
>you have to logged on as root to do this.
1. "hdc: multiple mode turned off" - What does this mean?
I recently installed a WD AC31600H hard drive and upgraded to RedHat
3.0.3 (kernel 1.2.13). When I boot up, I see the following:
Sat Feb 10 22:34:27 EST 1996
Partition check:
hda: hda1
hdb: hdb1 hdb2 hdb3 hdb4 < hdb5 >
hdc: multiple mode turned off
hdc: hdc1 hdc2 hdc3 hdc4 < hdc5 hdc6 >
What does the message "multiple mode turned off" mean? Does this mean
that multi-block transfers are disabled? If so, why is that? I have
my BIOS setting for multi-transfers set to "auto", and the disk is a
fairly recent model, so I assume it would support it.
Or is it saying the disk supports it, but not my motherboard's IDE
interface (note: it's not an EIDE interface). If this is the case,
then why would my BIOS ( MicroFirmware M4GS25, which is custom made
for this motherboard) even have a setting for it? Or is there
something else I need to set (the README.ide in the kernel source
didn't seem to say much about it other than it supports multiple block
mode).
Or is my ATAPI CD-ROM (which is a slave on the same interface (for
now)) messing it up?
Some additional info on my configuration:
Gateway 4DX2-66V, MicroFirmware M4GS25 BIOS
Primary IDE:
Master: WDC AC2340 (340MB Caviar)
Slave: WDC AC2340 (340MB Caviar)
Secondary IDE:
Master: WDC AC31600H (1.6GB Caviar)
Slave: TOSHIBA CD-ROM XM-5302TA, ATAPI
16 MB RAM
Running RedHat 3.0.3 (kernel 1.2.13)
Thanks for any help.
--
John A. Breen | I teleported home one night with Ron & Sid & Meg.
| - Douglas Adams
3. Turning off "automatic" STARTX command at boot time?
4. Redirecting request based on clients name/address
5. turn off "<" horizontal command line scrolling with ksh/bash?
6. ksh FTP
7. Can you turn "echo"ing off in custom shell command?
8. htaccess and limiting logins
9. GETSERVBYNAME()????????????????????"""""""""""""
10. "--mode compile" instead of "--mode=compile" problem with libtool
11. Driver performace "Kernel Mode" and "Module Mode"?
12. "write" "to" "flon" commands
13. """"""""My SoundBlast 16 pnp isn't up yet""""""""""""