2.1.200 pre 3 won't boot

2.1.200 pre 3 won't boot

Post by Davi » Fri, 08 May 1998 04:00:00

2.1.100 pre 3 hangs during boot on my Tyan Tomcat IV dual p166
machine. BusLogic BT-946C scsi controller. Here are the relevant boot
messages from 2.1.99 with

scsi: ***** BusLogic SCSI Driver Version 2.1.13 of 17 April 1998 *****

scsi0: Configuring BusLogic Model BT-946C PCI SCSI Host Adapter
scsi0:   Firmware Version: 4.19, I/O Address: 0x334, IRQ Channel: 17/Level
scsi0:   PCI Bus: 0, Device: 19, Address: Unassigned, Host Adapter SCSI ID: 7
scsi0:   Parity Checking: Enabled, Extended Translation: Enabled
scsi0:   Synchronous Negotiation: Fast, Wide Negotiation: Disabled
scsi0:   Disconnect/Reconnect: Enabled, Tagged Queuing: Disabled
scsi0:   Scatter/Gather Limit: 128 of 8192 segments, Mailboxes: 211
scsi0:   Driver Queue Depth: 211, Host Adapter Queue Depth: 100
scsi0:   Tagged Queue Depth: Automatic, Untagged Queue Depth: 3
scsi0:   Error Recovery Strategy: Default, SCSI Bus Reset: Enabled
scsi0:   SCSI Bus Termination: Enabled
scsi0: *** BusLogic BT-946C Initialized Successfully ***
scsi0 : BusLogic BT-946C
scsi : 1 host.

**** 2.1.100 pre 3 hangs here ****

  Vendor: SEAGATE   Model: ST15150N          Rev: 0023
  Type:   Direct-Access                      ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
  Vendor: PIONEER   Model: CD-ROM DR-124X    Rev: 1.01
  Type:   CD-ROM                             ANSI SCSI revision: 02
Detected scsi CD-ROM sr0 at scsi0, channel 0, id 1, lun 0
  Vendor: CONNER    Model: CTT8000-S         Rev: 1.17
  Type:   Sequential-Access                  ANSI SCSI revision: 02
Detected scsi tape st0 at scsi0, channel 0, id 4, lun 0
scsi0: Target 0: Queue Depth 3, Synchronous at 10.0 MB/sec, offset 15
scsi0: Target 1: Queue Depth 3, Synchronous at 4.55 MB/sec, offset 8
scsi0: Target 4: Queue Depth 3, Synchronous at 5.00 MB/sec, offset 15
scsi : detected 1 SCSI tape 1 SCSI cdrom 1 SCSI disk total.
sr0: scsi3-mmc drive: 4x/4x xa/form2 cdda tray

     David Walker          !                    World Wide Web

                           !          <ftp://ftp.eskimo.com/u/d/dwalker/>


1. AS 200 4/233 won't boot - unknown LED code

I have an AlphaStation200 4/233 that has been running Linux fine until
the other day when it crashed on me. I rebooted and I don't get any beep
codes but the console doesn't start either. The LED codes I have are all
8 bits are lit except bit 1 and bit 3 which are off(yes - 1 and 3 are
off). My alphastation manual does not list what this error code means -
anyone have an idea what hardware to try replacing?

The most recent peice of HW I put into the system was a used PCI VGA
card which I switch back to my original ISA VGA card with no luck.

I've heard that the power supplies in the Multias often fail - should I
try getting a new power supply?

Sent via Deja.com http://www.deja.com/
Before you buy.

2. pkgadd question

3. redhat 7.2 and win 2k pro-->boot loaders do not recognize win 200

4. XFree86-3.2 and S3 Trio64V+

5. 2.3 pre-4 won't boot

6. Solaris 9 X86 with Windows XP on the same drive...

7. X Display won't go above 320 X 200

8. "month" utility?

9. NetBSD pmax 1.4.1 Won't reboot on 5000/200

10. FreeBSD 4.2 won't boot - 'read error' on boot after install

11. Sparc 20 won't boot and won't display errors, either.

12. *** lilo won't boot win' 95 ***

13. Sparc 20 won't boot and won't display errors, either.