2.2.19/ide.03252001 bug: "kernel timer added twice"

2.2.19/ide.03252001 bug: "kernel timer added twice"

Post by Matthias Andre » Fri, 13 Apr 2001 18:50:06



I just spotted these messages in my xconsole:

Apr 12 11:22:19 emma1 kernel: hda: status error: status=0x50 { DriveReady SeekComplete }
Apr 12 11:22:19 emma1 kernel: hda: no DRQ after issuing MULTWRITE
Apr 12 11:22:19 emma1 kernel: hda: ide_set_handler: handler not null; old=c01acc04, new=c01acc04
Apr 12 11:22:19 emma1 kernel: bug: kernel timer added twice at c01a835d.

My system.map mentions these in the vicinity of that address:
c01a8308 T ide_set_handler
c01a836c T current_capacity

The mentioned ide_set_handler:
c01acc04 T task_no_data_intr

The kernel has been compiled with gcc 2.95.2 with some other patches
which should not interfere however. (IDE 2.2.19.03252001, I2C 2.5.5,
ReiserFS 3.5.32, Serial 5.05, autofs4 from 4.0.0pre10, ext3 0.0.6b,
OpenWall OW1 patch)

I cannot tell what has happened exactly, at the time of this writing,
I'm running amanda (backup) which comprises dump and tar and this
message has not shown up again in the past 16 minutes.

This is a Western Digital Caviar AC420400D (seems to be IBM DJNA OEM)
attached to a VIA KT133 (board is a Gigabyte 7ZXR):

lspci info:

00:07.1 IDE interface: VIA Technologies, Inc. VT82C586 IDE [Apollo] (rev 10) (pr
        Flags: bus master, medium devsel, latency 32
        I/O ports at ffa0
        Capabilities: [c0] Power Management version 2

hdparm v3.6 info:

/dev/hda:
 multcount    = 16 (on)
 I/O support  =  1 (32-bit)
 unmaskirq    =  1 (on)
 using_dma    =  1 (on)
 keepsettings =  0 (off)
 nowerr       =  0 (off)
 readonly     =  0 (off)
 readahead    =  8 (on)
 geometry     = 2482/255/63, sectors = 39876480, start = 0

 Model=WDC AC420400D, FwRev=J58OA30K, SerialNo=[NOT SHOWN]
 Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
 RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=34
 BuffType=3(DualPortCache), BuffSize=1966kB, MaxMultSect=16, MultSect=16
 DblWordIO=no, OldPIO=2, DMA=yes, OldDMA=2
 CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=39876480
 tDMA={min:120,rec:120}, DMA modes: mword0 mword1 mword2
 IORDY=on/off, tPIO={min:240,w/IORDY:120}, PIO modes: mode3 mode4
 UDMA modes: mode0 mode1 mode2 mode3 *mode4
 Drive Supports : ATA/ATAPI-4 T13 1153D revision 17 : ATA-1 ATA-2 ATA-3 ATA-4

--
Matthias Andree
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in

More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/