2.5.7-dj1 add 5 help texts to arch/cris/Config.help

2.5.7-dj1 add 5 help texts to arch/cris/Config.help

Post by Steven Col » Wed, 27 Mar 2002 11:00:21



This patch adds 5 help texts to arch/cris/Config.help.
The texts were obtained from ESR's v2.97 Configure.help.

Steven

--- linux-2.5.7-dj1/arch/cris/Config.help.orig  Mon Mar 25 13:53:25 2002

 CONFIG_ETRAX_RESCUE_SER3
   Use serial port 3 as the rescue port.

+CONFIG_ETRAX_POWERBUTTON_BIT
+  Configure where power button is connected.
+
+CONFIG_ETRAX_ROOT_DEVICE
+  Specifies the device that should be mounted as root file system
+  when booting from flash. The axisflashmap driver adds an additional
+  mtd partition for the appended root file system image, so this option
+  should normally be the mtdblock device for the partition after the
+  last partition in the partition table.
+
+CONFIG_ETRAX_SHUTDOWN_BIT
+  Configure what pin on CSPO-port that is used for controlling power
+  supply.
+
+CONFIG_ETRAX_SOFT_SHUTDOWN
+  Enable this if Etrax is used with a power-supply that can be turned
+  off and on with PS_ON signal. Gives the possibility to detect
+  powerbutton and then do a power off after unmounting disks.
+
+CONFIG_ETRAX_WATCHDOG_NICE_DOGGY
+  By enabling this you make sure that the watchdog does not bite while
+  printing oopses. Recommended for development systems but not for
+  production releases.

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in

More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

 
 
 

1. 2.5.7-dj1 add 6 help texts to arch/cris/drivers/Config.help

This patch adds 6 help texts to arch/cris/drivers/Config.help.
The texts were obtained from ESR's v2.97 Configure.help.

Steven

--- linux-2.5.7-dj1/arch/cris/drivers/Config.help.orig  Mon Mar 25 13:52:21 2002

 CONFIG_ETRAX_PARALLEL_PORT1
   Say Y here to enable parallel port 1.

+CONFIG_ETRAX_ETHERNET_LPSLAVE
+  This option enables a slave ETRAX 100 or ETRAX 100LX, connected to a
+  master ETRAX 100 or ETRAX 100LX through par0 and par1, to act as an
+  Ethernet controller.
+
+CONFIG_ETRAX_ETHERNET_LPSLAVE_HAS_LEDS
+  Enable if the slave has it's own LEDs.
+
+CONFIG_ETRAX_IDE
+  Enable this to get support for ATA/IDE.  You can't use parallel
+  ports or SCSI ports at the same time.
+
+CONFIG_ETRAX_NETWORK_LED_ON_WHEN_ACTIVITY
+  Selecting LED_on_when_link will light the LED when there is a
+  connection and will flash off when there is activity.
+
+  Selecting LED_on_when_activity will light the LED only when
+  there is activity.
+
+  This setting will also affect the behaviour of other activity LEDs
+  e.g. Bluetooth.
+
+CONFIG_ETRAX_NETWORK_LED_ON_WHEN_LINK
+  Selecting LED_on_when_link will light the LED when there is a
+  connection and will flash off when there is activity.
+
+  Selecting LED_on_when_activity will light the LED only when
+  there is activity.
+
+  This setting will also affect the behaviour of other activity LEDs
+  e.g. Bluetooth.
+
+CONFIG_ETRAX_SERIAL_PORT0
+  Enables the ETRAX 100 serial driver for ser0 (ttyS0)
+  Normally you want this on, unless you use external DMA 1 that uses
+  the same DMA channels.

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in

More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

2. Prometheus ProModem Ultima Setup

3. 2.5.7-dj1, add 3 help texts to arch/alpha/Config.help

4. {SLRN} 'Autoposting' ..?

5. 2.5.8-dj1, add five help texts to arch/ppc/Config.help

6. qfe* wont come up

7. 2.5.7-dj1, add 3 help texts to arch/mips/Config.help

8. rpm stopped working?

9. 2.5.8-dj1, add 22 help texts to arch/arm/Config.help

10. 2.5.9-dj1, add one help text to arch/ia64/Config.help.

11. 2.5.9-dj1, add to help text in arch/s390/Config.help.

12. 2.5.7-dj1, add 2 help texts to arch/s390/Config.help

13. 2.5.5-dj1 add one help text to drivers/char/drm/Config.help