2.4.20-pre5-ac1 and Intel ICH3M EIDE woes

2.4.20-pre5-ac1 and Intel ICH3M EIDE woes

Post by Alexander Hoogerhui » Sun, 01 Sep 2002 22:50:06



I used to run 2.5.x as my laptop has the Intel ICH3M chips in it, and
on the plain 2.4.x it would fail during boot claiming "resource
collisions". In 2.4.19-ac4 or thereabouts it seemed to have been fixed
the the ac-releases, and I ran happily with 2.4 again. After seeing a
lot of IDE rearrangements lately I thought it was time for a YANK (Yet
Another New Kernel), and the ICH3M seems unhappy again about resource
collisions:

ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH3M: IDE controller at PCI slot 00:1f.1
PCI: Device 00:1f.1 not available because of resource collisions
PCI: Assigned IRQ 11 for device 00:1f.1
ICH3M: Not fully BIOS configured!
ICH3M: chipset revision 2
ICH3M: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0x4440-0x4447, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0x4448-0x444f, BIOS settings: hdc:DMA, hdd:pio
hda: TOSHIBA MK4019GAX, ATA DISK drive
hdc: SD-R2102, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: host protected area => 1
hda: 78140160 sectors (40008 MB), CHS=5168/240/63, UDMA(100)
hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, DMA
Uniform CD-ROM driver Revision: 3.12
Partition check:
 hda: hda1 hda2 hda3

However, unlike back in 2.4.18, this time I can run hdparm and get it
to run in UDMA mode (instead of the default PIO mode) and get the
performance back.

Relevant bits of the .config:

lapper:~/src/linux/linux-2.4-test$ grep IDE .config | grep -v ^# | sort
CONFIG_BLK_DEV_IDECD_BAILOUT=y
CONFIG_BLK_DEV_IDECD=y
CONFIG_BLK_DEV_IDEDISK=y
CONFIG_BLK_DEV_IDEDMA_PCI=y
CONFIG_BLK_DEV_IDEDMA=y
CONFIG_BLK_DEV_IDEFLOPPY=m
CONFIG_BLK_DEV_IDE_MODES=y
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_BLK_DEV_IDESCSI=y
CONFIG_BLK_DEV_IDETAPE=m
CONFIG_BLK_DEV_IDE=y
CONFIG_IDEDISK_MULTI_MODE=y
CONFIG_IDEDISK_STROKE=y
CONFIG_IDEDMA_AUTO=y
CONFIG_IDEDMA_PCI_AUTO=y
CONFIG_IDEPCI_SHARE_IRQ=y
CONFIG_IDE_TASKFILE_IO=y
CONFIG_IDE_TASK_IOCTL=y
CONFIG_IDE=y
CONFIG_IEEE1394_VIDEO1394=m
lapper:~/src/linux/linux-2.4-test$

mvh,
A
--

CCNP - CCDP - MCNE - CCSE                          | +47 908 21 485
"You have zero privacy anyway. Get over it."  --Scott McNealy
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in

More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

 
 
 

2.4.20-pre5-ac1 and Intel ICH3M EIDE woes

Post by Alan Co » Mon, 02 Sep 2002 00:10:09



> ICH3M: IDE controller at PCI slot 00:1f.1
> PCI: Device 00:1f.1 not available because of resource collisions
> PCI: Assigned IRQ 11 for device 00:1f.1
> ICH3M: Not fully BIOS configured!

Looks fine to me. We reconfigured the relevant bits

Quote:> ICH3M: chipset revision 2
> ICH3M: not 100% native mode: will probe irqs later
>     ide0: BM-DMA at 0x4440-0x4447, BIOS settings: hda:DMA, hdb:pio
>     ide1: BM-DMA at 0x4448-0x444f, BIOS settings: hdc:DMA, hdd:pio

And you got full DMA

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in

More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/