Board index Unix Web Servers

403 Error with Apache ver 1.3.24 RH7.3

403 Error with Apache ver 1.3.24 RH7.3

Post by Christiaan Ehler » Wed, 19 Jun 2002 21:53:31



I have installed linux RH7.3 with apache1.3.24... On the default (no
tweeking) I get a Error 403.  In httpd.conf I have DocumentRoot
"/usr/local/apache/htdocs" the permisions on that directory is drwxr-xr-x
thus I assume all can read that directory.  I have created a index.html with
permissions -rwxrwxrwx, and it still comes up with an error 403.

From the linux box I open mozilla and try and surf to the site and it says
Forbidden.

I have no firewall installed on the server.

I have read the postings of Ming He (et al) he is using RH6.2 and
apache1.3.22 would the problems be the same?

Kind Regards
Christiaan Ehlers

 
 
 
Top

403 Error with Apache ver 1.3.24 RH7.3

Post by 2Host.co » Thu, 20 Jun 2002 04:38:39



> I have installed linux RH7.3 with apache1.3.24... On the default (no
> tweeking) I get a Error 403.  In httpd.conf I have DocumentRoot
> "/usr/local/apache/htdocs" the permisions on that directory is drwxr-xr-x
> thus I assume all can read that directory.  I have created a index.html with
> permissions -rwxrwxrwx, and it still comes up with an error 403.

> From the linux box I open mozilla and try and surf to the site and it says
> Forbidden.

> I have no firewall installed on the server.

> I have read the postings of Ming He (et al) he is using RH6.2 and
> apache1.3.22 would the problems be the same?

Do you have index.html configured to be a default index file? Do you
have any Limits imposed? I.e., allow,deny and you're denying access to
said directory? What does your error log report? BTW, you don't need to
set the index file at 777. Just set it to 644 and it should work just
fine. Everything else appears to be okay, but there could be a few
reasons why it's not working that we can't see from this.

Regards,
Robert
--

Server administrator/support - 2Host.com web hosting.
Secure, reliable hosting - What you expect & deserve!
How are we different? Find out: http://www.2host.com/

 
 
 
Top

1. Apache 1.3.24 startup error on Solaris 8 _floatdisf error

The following error occurs when I try to start Apache:
apacheserver# ./apachectl start
Syntax error on line 214 of /usr/local/apache/conf/httpd.conf:Cannot
load /usr/local/apache/libexec/mod_negotiation.so into server:
ld.so.1: /usr/local/apache/bin/httpd: fatal: relocation error:file
/usr/local/apache/libexec/mod_negotiation.so: symbol __floatdisf:
referenced symbol not found
./apachectl start: httpd could not be started

I can comment this module in httpd.conf, but I get the same error for
mod_proxy.
After commenting the line for mod_proxy in httpd.conf.  I do get
apache to start up.

I was wondering if there is a workaround to the above error as I would
like apache to be compiled with all modules.  I have seen a lot of
questions regarding the above on the net, but am yet to find the
solution for it.

I have compiled apache with 2.95, 3.03 and 3.04 with and without
binutils.  I am using
perl 5.6.0
openssl0.9.6c
mod_ssl2.8.8-1.3.24
apache1.3.24 and
mod_perl1.26

I am building apache, via mod_perl
My configure in mod_perl is posted below
perl Makefile.PL USE_APACI=1 EVERYTHING=1 \
APACHE_SRC=../apache_1.3.x/src \
SSL_BASE=/usr/local/ssl \
APACHE_PREFIX=/usr/local/apache \
APACI_ARGS=--with-layout=Apache,--enable-module=all,--enable-shared=max,--disable-module=auth_db,--disable-shared=perl,--enable-rule=SSL_EXPERIMENTAL

Any suggestion would help.  I don't have SUN's compiler (cc) and would
like to use gcc.

Thanks

2. RivaTNT+XF86401+GLX095=not working!

3. DHCP/Masquerading note

4. Apache 1.3.24 make install error

5. Solaris 2.2 and /dev/ptmx errors. What is it?

6. Apache 1.3.24 + mod_perl 1.26 + ipv6 patch build fails

7. lsvirprt - where is the ascii file for me to see

8. apache 1.3.24 htaccess/symbolic link problem

9. Problem building Apache 1.3.24 on Solaris 8

10. Apache 1.3.24 - mod_proxy

11. Apache 1.3.24 is vulnerable

12. apache 1.3.24


All times are UTC
Board index