USB Compact Flash Reader, Help with setup

USB Compact Flash Reader, Help with setup

Post by Jason Dento » Sat, 02 Dec 2000 04:00:00



I am trying to get the compact flash card reader that came with my I-Jam
50 setup. It is a USB mass storage device, I'm running 4.2 Release #4. I
have the following devices in my kernel config :

device uchi
device usb
device ugen
device umass
device scbus
device da
device pass

The order above is the order in which the appear in the config file
(this makes a difference I thing).

I do make depend, make, make install, and reboot. The kernel does
correctly prode the device at boot time, I get :

usb0: <VIA 83C572 USB controller> on uhci0
usb0: USB revision 1.0
uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
ugen0: SHUTTLE SCM Micro USBAT-02 , rev 1.00/0.05, addr 2
uhci1: <VIA 83C572 USB controller> port 0xd800-0xd81f irq 10 at device
4.3 on pc
i0SC[A
usb1: <VIA 83C572 USB controller> on uhci1
usb1: USB revision 1.0
uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered

camcontrol devlist -v give me:
scbus-1 on xpt0 bus 0:
<  >                               at scbus-1 target -1 lun -1 (xpt0)

camcontrol rescan 0 gives me :
camcontrol: CAMIOCOMMAND ioctl failed: Invalid argument

and when I try to mount I get
mount -t msdos /dev/da0 /mnt/flash
msdos: /dev/da0: Device not configured

I think part of the problem is that I do not have a SCSI adapter in the
system and the scsi code isn't getting activated, but I'm not sure. Does
anybody have a solution, or thought on what to try next?

Jason Denton

 
 
 

1. Help mounting a USB Compact Flash Reader with 64MB card

Hey all,

I've managed to start an install for OpenBSD, but I want to install to a
compact flash card.

dmesg says the card is there as sd0c, but I can't mount it because of
the following messages:

sd0: mode sense (5) return nonsense; using fictitiuous geometery
sd0(umass0:0:0): Ckech Condition on opcode 0x8
   SENSE KEY: Illegal Request
   ADSC/ASCQ: ASC 0x20 ASCQ 0x00

Here's what dmesg says about the drive:

emBSD 2.0-stable (RAMDISK_CD) #4: Tue Mar 5 08:40:08 EST 2002
(emBSD is based off of OpenBSD-current)
...

umass0 at uhub0 port 2 configuration 1 interface 0
umass0: vendor 0.090c CF Reader, rev 1.00/1.00, addr 2
umass0: using SCSI over BBB-P
scsibus1 at umass0: 2 targets
sd at scsibus1 targ 1 lun 0: <, CF Reader, 1.04> SCSI0 0/direct removable
sd0: mode sense (5) returned nonsense; using fictitious geometry
sd0: 62MB, 62 cyl, 64 head, 32 sec, 512 bytes/sec, 128832 sec total
(and then repeat the above messages)

Any ideas on how to get this thing to mount and install properly?

James

2. CDROM Rip rate

3. Help recognizing USB Compact Flash Reader and card

4. disable power-switch on keyborad

5. USB Compact Flash Readers

6. Reply to All

7. SanDisk Compact Flash USB Reader (SDDR-31): WHICH DEVICE?

8. vt100 Menuing system

9. Boot from USB compact flash reader...?

10. block devices & module leading & USB Compact Flash readers

11. USB compact flash readers anyone?

12. USB Compact Flash Card Reader from SCM Micro

13. How to use USB compact flash reader in RH8