Initio SCSI adapter

Initio SCSI adapter

Post by Daniel McGrego » Fri, 15 Oct 1999 04:00:00



Hello all.

        I have a few questions.  I have an Initio IHA-9090U controlling my
cd burner.  While I know this board isn't supported in the default FreeBSD
kernel, I have added support from www.ioiscsi.com/bios.html.  Anyway, why
hasn't it been included in the kernel source tree?

        Also, when I boot the system, if I do have a disc in the drive,
I get kernel messages like this, while if I don't have a disc in the drive
the kernel complains and says it has deleted the cd0 device.  Is there
any way to make it work so that it will work with either a disc or not?

Also, if you'll notice the wdc1 not found bit,  It is there, it works in
OpenBSD and Linux, and my CD-ROM drive is on it.  I have an Intel PCI
controller, any ideas?

Copyright (c) 1992-1999 FreeBSD Inc.
Copyright (c) 1982, 1986, 1989, 1991, 1993
        The Regents of the University of California. All rights reserved.
FreeBSD 3.3-STABLE #0: Mon Oct 11 21:23:10 CST 1999

Timecounter "i8254"  frequency 1193182 Hz
CPU: Pentium II (233.86-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x633  Stepping = 3
  Features=0x80f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,MMX>
real memory  = 67108864 (65536K bytes)
avail memory = 62222336 (60764K bytes)
Preloaded elf kernel "kernel" at 0xc02e8000.
Pentium Pro MTRR support enabled
Probing for devices on PCI bus 0:
chip0: <Intel 82443LX host to PCI bridge> rev 0x03 on pci0.0.0
chip1: <Intel 82443LX PCI-PCI bridge> rev 0x03 on pci0.1.0
chip2: <Intel 82371AB PCI to ISA bridge> rev 0x01 on pci0.7.0
ide_pci0: <Intel PIIX4 Bus-master IDE controller> rev 0x01 on pci0.7.1
chip3: <Intel 82371AB Power management controller> rev 0x01 on pci0.7.3
iha0: <IOI IOI-9X00UW PCI SCSI adapter> rev 0x02 int a irq 10 on pci0.11.0
iha0: Reset SCSI Bus ...
ed1: <NE2000 PCI Ethernet (RealTek 8029)> rev 0x00 int a irq 11 on pci0.12.0
ed1: address 00:60:67:2d:0a:15, type NE2000 (16 bit)
Probing for devices on PCI bus 1:
vga0: <Matrox model 0521 graphics accelerator> rev 0x01 int a irq 9 on pci1.0.0
Probing for PnP devices:
CSN 1 Vendor ID: MOT15f0 [0xf015f435] Serial 0x0565f5ef Comp ID: MOT15f0 [0xf015f435]
CSN 2 Vendor ID: CTL00e4 [0xe4008c0e] Serial 0x11161901 Comp ID: PNPb02f [0x2fb0d041]
Probing for devices on the ISA bus:
sc0 on isa
sc0: VGA color <16 virtual consoles, flags=0x0>
atkbdc0 at 0x60-0x6f on motherboard
atkbd0 irq 1 on isa
sio0 at 0x3f8-0x3ff irq 4 flags 0x10 on isa
sio0: type 16550A
sio1 at 0x2f8-0x2ff irq 3 on isa
sio1: type 16550A
fdc0 at 0x3f0-0x3f7 irq 6 drq 2 on isa
fdc0: FIFO enabled, 8 bytes threshold
fd0: 1.44MB 3.5in
wdc0 at 0x1f0-0x1f7 irq 14 flags 0xa0ffa0ff on isa
wdc0: unit 0 (wd0): <QUANTUM FIREBALL ST3.2A>, DMA, 32-bit, multi-block-16
wd0: 3079MB (6306048 sectors), 6256 cyls, 16 heads, 63 S/T, 512 B/S
wdc0: unit 1 (wd1): <IBM-DALA-3540>, 32-bit, multi-block-16
wd1: 516MB (1057392 sectors), 1049 cyls, 16 heads, 63 S/T, 512 B/S
wdc1 not found at 0x170
ppc0 at 0x378 irq 7 flags 0x40 on isa
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
ppb0: IEEE1284 device found /NIBBLE/ECP
Probing for PnP devices on ppbus0:
ppbus0: <HEWLETT-PACKARD DESKJET 880C> MLC,PCL,PML
lpt0: <generic printer> on ppbus 0
lpt0: Interrupt-driven port
ppi0: <generic parallel i/o> on ppbus 0
plip0: <PLIP network interface> on ppbus 0
vga0 at 0x3b0-0x3df maddr 0xa0000 msize 131072 on isa
npx0 on motherboard
npx0: INT 16 interface
apm0 flags 0x31 on isa
apm: found APM BIOS version 1.2
sb0 at 0x220 irq 5 drq 1 on isa
snd0: <SoundBlaster 16 4.16>
sbxvi0 at drq 5 on isa
snd0: <SoundBlaster 16 4.16>
sbmidi0 at 0x330 on isa
snd0: <SoundBlaster MPU-401>
Waiting 15 seconds for SCSI devices to settle
changing root device to wd0s2a
cd0 at iha0 bus 0 target 6 lun 0
cd0: <SONY CD-R   CDU948S 1.0e> Removable CD-ROM SCSI-2 device
cd0: 20.000MB/s transfers (20.000MHz, offset 15)
cd0: cd present [726 x 2048 byte records]


---
Q:  How much money do you give to a 900 foot Jesus?
A:  As much as he wants.

 
 
 

Initio SCSI adapter

Post by Thierry Herbelo » Fri, 15 Oct 1999 04:00:00


Hello,

For the initio source code, I seem to remember there are copyright
mentions in the initio code : that may be the reason why it is not
included in the base source tree (and maintained).

For your wdc1 : is there something connected to your second IDE drive ?

        TfH


> Hello all.

>         I have a few questions.  I have an Initio IHA-9090U controlling my
> cd burner.  While I know this board isn't supported in the default FreeBSD
> kernel, I have added support from www.ioiscsi.com/bios.html.  Anyway, why
> hasn't it been included in the kernel source tree?

>         Also, when I boot the system, if I do have a disc in the drive,
> I get kernel messages like this, while if I don't have a disc in the drive
> the kernel complains and says it has deleted the cd0 device.  Is there
> any way to make it work so that it will work with either a disc or not?

> Also, if you'll notice the wdc1 not found bit,  It is there, it works in
> OpenBSD and Linux, and my CD-ROM drive is on it.  I have an Intel PCI
> controller, any ideas?

> Copyright (c) 1992-1999 FreeBSD Inc.
> Copyright (c) 1982, 1986, 1989, 1991, 1993
>         The Regents of the University of California. All rights reserved.
> FreeBSD 3.3-STABLE #0: Mon Oct 11 21:23:10 CST 1999

> Timecounter "i8254"  frequency 1193182 Hz
> CPU: Pentium II (233.86-MHz 686-class CPU)
>   Origin = "GenuineIntel"  Id = 0x633  Stepping = 3
>   Features=0x80f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,MMX>
> real memory  = 67108864 (65536K bytes)
> avail memory = 62222336 (60764K bytes)
> Preloaded elf kernel "kernel" at 0xc02e8000.
> Pentium Pro MTRR support enabled
> Probing for devices on PCI bus 0:
> chip0: <Intel 82443LX host to PCI bridge> rev 0x03 on pci0.0.0
> chip1: <Intel 82443LX PCI-PCI bridge> rev 0x03 on pci0.1.0
> chip2: <Intel 82371AB PCI to ISA bridge> rev 0x01 on pci0.7.0
> ide_pci0: <Intel PIIX4 Bus-master IDE controller> rev 0x01 on pci0.7.1
> chip3: <Intel 82371AB Power management controller> rev 0x01 on pci0.7.3
> iha0: <IOI IOI-9X00UW PCI SCSI adapter> rev 0x02 int a irq 10 on pci0.11.0
> iha0: Reset SCSI Bus ...
> ed1: <NE2000 PCI Ethernet (RealTek 8029)> rev 0x00 int a irq 11 on pci0.12.0
> ed1: address 00:60:67:2d:0a:15, type NE2000 (16 bit)
> Probing for devices on PCI bus 1:
> vga0: <Matrox model 0521 graphics accelerator> rev 0x01 int a irq 9 on pci1.0.0
> Probing for PnP devices:
> CSN 1 Vendor ID: MOT15f0 [0xf015f435] Serial 0x0565f5ef Comp ID: MOT15f0 [0xf015f435]
> CSN 2 Vendor ID: CTL00e4 [0xe4008c0e] Serial 0x11161901 Comp ID: PNPb02f [0x2fb0d041]
> Probing for devices on the ISA bus:
> sc0 on isa
> sc0: VGA color <16 virtual consoles, flags=0x0>
> atkbdc0 at 0x60-0x6f on motherboard
> atkbd0 irq 1 on isa
> sio0 at 0x3f8-0x3ff irq 4 flags 0x10 on isa
> sio0: type 16550A
> sio1 at 0x2f8-0x2ff irq 3 on isa
> sio1: type 16550A
> fdc0 at 0x3f0-0x3f7 irq 6 drq 2 on isa
> fdc0: FIFO enabled, 8 bytes threshold
> fd0: 1.44MB 3.5in
> wdc0 at 0x1f0-0x1f7 irq 14 flags 0xa0ffa0ff on isa
> wdc0: unit 0 (wd0): <QUANTUM FIREBALL ST3.2A>, DMA, 32-bit, multi-block-16
> wd0: 3079MB (6306048 sectors), 6256 cyls, 16 heads, 63 S/T, 512 B/S
> wdc0: unit 1 (wd1): <IBM-DALA-3540>, 32-bit, multi-block-16
> wd1: 516MB (1057392 sectors), 1049 cyls, 16 heads, 63 S/T, 512 B/S
> wdc1 not found at 0x170
> ppc0 at 0x378 irq 7 flags 0x40 on isa
> ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
> ppb0: IEEE1284 device found /NIBBLE/ECP
> Probing for PnP devices on ppbus0:
> ppbus0: <HEWLETT-PACKARD DESKJET 880C> MLC,PCL,PML
> lpt0: <generic printer> on ppbus 0
> lpt0: Interrupt-driven port
> ppi0: <generic parallel i/o> on ppbus 0
> plip0: <PLIP network interface> on ppbus 0
> vga0 at 0x3b0-0x3df maddr 0xa0000 msize 131072 on isa
> npx0 on motherboard
> npx0: INT 16 interface
> apm0 flags 0x31 on isa
> apm: found APM BIOS version 1.2
> sb0 at 0x220 irq 5 drq 1 on isa
> snd0: <SoundBlaster 16 4.16>
> sbxvi0 at drq 5 on isa
> snd0: <SoundBlaster 16 4.16>
> sbmidi0 at 0x330 on isa
> snd0: <SoundBlaster MPU-401>
> Waiting 15 seconds for SCSI devices to settle
> changing root device to wd0s2a
> cd0 at iha0 bus 0 target 6 lun 0
> cd0: <SONY CD-R   CDU948S 1.0e> Removable CD-ROM SCSI-2 device
> cd0: 20.000MB/s transfers (20.000MHz, offset 15)
> cd0: cd present [726 x 2048 byte records]


> ---
> Q:  How much money do you give to a 900 foot Jesus?
> A:  As much as he wants.


 
 
 

Initio SCSI adapter

Post by Daniel McGrego » Fri, 15 Oct 1999 04:00:00



> Hello,

> For the initio source code, I seem to remember there are copyright
> mentions in the initio code : that may be the reason why it is not
> included in the base source tree (and maintained).

> For your wdc1 : is there something connected to your second IDE drive ?

Only my IDE CD-ROM drive is connected to wdc1.  It is the slave drive
with no master.  Maybe if I switch it to master?
 
 
 

1. Initio SCSI adapters?

I have a SIIG SCSI350P Ultra Wide SCSI adapter.  It uses an Initio
INI-9200U/UW chipset.  I'm getting a copy of OpenBSD to fiddle with,
in addition to the custom Linux installation that I have.  Does
anybody know of OpenBSD drivers for this SCSI board?  Right now I just
have my CD-ROM drive attached to it, but I'm thinking of getting some
SCSI HDs, and I'd like to be able to use them under OpenBSD.

--
Christian Allred
NT Service Packs
28/2058
(70) x39960

2. openbsd 3.3 gcc bug ??

3. Initio UltraWide SCSI adapters?

4. Where are gcc binaries for Solaris 2.4/x86

5. Initio 9100UW SCSI adapter

6. Problem with hard disk

7. SCSI: Does one need a special SCSI LVD adapter, over and above a SCSI card?

8. how to use the automounter with ncpfs.

9. initio scsi add in

10. ISA SCSI card INITIO 6100

11. Initio INI-9100 SCSI card, How to Install RedHat 5.1????

12. Looking for coments on Initio SCSI controllers

13. initio scsi prob