Board index Freebsd

FreeBSD 4.3-RELEASE: Various applications core-dump

FreeBSD 4.3-RELEASE: Various applications core-dump

Post by Thomas Amrei » Wed, 06 Jun 2001 00:36:43



Hi,

I installed FreeBSD 4.3-RELEASE.
Various software core-dumps on my machine and I have no clue why (The
OpenSSH daemon provided with FreeBSD4.3, Apache 1.3.20, . ...). After reboot
other or same software core-dumps, sometimes software works again till next
reboot.
BIOS memory-checking does not report any defective RAM.
I have an ASUS P/I-55T2P4 motherboard, Matrox Millenium 2064W graphics
adapter, Linksys LNE100TX NIC, IDE Harddisk and CDROM (see dmesg).

Anyone knows what's wrong here?

Thanks for help,

Tom

########################
Things I found in /var/log/messages:

pid 228 (inetd), uid 0: exited on signal 11 (core dumped)
pid 229 (inetd), uid 0: exited on signal 11 (core dumped)
pid 230 (inetd), uid 0: exited on signal 11 (core dumped)
pid 231 (sshd), uid 0: exited on signal 11 (core dumped)
.....
dc0: TX underrun -- increasing TX threshold
pid 372 (httpd), uid 65534: exited on signal 11
pid 374 (httpd), uid 65534: exited on signal 11
pid 375 (httpd), uid 65534: exited on signal 11

########################
This is output from dmesg:

Copyright (c) 1992-2001 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 4.3-RELEASE #0: Sat Apr 21 10:54:49 GMT 2001

Timecounter "i8254"  frequency 1193182 Hz
CPU: Pentium/P54C (166.19-MHz 586-class CPU)
  Origin = "GenuineIntel"  Id = 0x52c  Stepping = 12
  Features=0x1bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8>
real memory  = 67108864 (65536K bytes)
avail memory = 60956672 (59528K bytes)
Preloaded elf kernel "kernel" at 0xc044d000.
Intel Pentium detected, installing workaround for F00F bug
md0: Malloc disk
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
isab0: <Intel 82371SB PCI to ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX3 ATA controller> port 0xe800-0xe80f at device 7.1 on
pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
dc0: <ADMtek AN985 10/100BaseTX> port 0xe000-0xe0ff mem
0xe6000000-0xe60003ff irq 10 at device 10.0 on pci0
dc0: Ethernet address: 00:04:5a:45:4a:2e
miibus0: <MII bus> on dc0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pci0: <Matrox MGA Millennium 2064W graphics accelerator> at 12.0 irq 11
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
ad0: 2067MB <IBM-DAQA-32160> [4200/16/63] at ata0-master WDMA2
acd0: CDROM <ATAPI 50X CDROM> at ata1-master using PIO4
Mounting root from ufs:/dev/ad0s1a

 
 
 
Top

FreeBSD 4.3-RELEASE: Various applications core-dump

Post by Jamie Norwo » Wed, 06 Jun 2001 00:59:52



>Hi,

>I installed FreeBSD 4.3-RELEASE.
>Various software core-dumps on my machine and I have no clue why (The
>OpenSSH daemon provided with FreeBSD4.3, Apache 1.3.20, . ...). After reboot
>other or same software core-dumps, sometimes software works again till next
>reboot.

It is your memory, most likely.

Quote:>BIOS memory-checking does not report any defective RAM.

BIOS memory check isn't worth the bits it prints on the screen. Try it with
better memory and see if it improves. Sig 11 indicates a hardware problem.

Jamie

>I have an ASUS P/I-55T2P4 motherboard, Matrox Millenium 2064W graphics
>adapter, Linksys LNE100TX NIC, IDE Harddisk and CDROM (see dmesg).

>Anyone knows what's wrong here?

>Thanks for help,

>Tom

>########################
>Things I found in /var/log/messages:

>pid 228 (inetd), uid 0: exited on signal 11 (core dumped)
>pid 229 (inetd), uid 0: exited on signal 11 (core dumped)
>pid 230 (inetd), uid 0: exited on signal 11 (core dumped)
>pid 231 (sshd), uid 0: exited on signal 11 (core dumped)
>.....
>dc0: TX underrun -- increasing TX threshold
>pid 372 (httpd), uid 65534: exited on signal 11
>pid 374 (httpd), uid 65534: exited on signal 11
>pid 375 (httpd), uid 65534: exited on signal 11

>########################
>This is output from dmesg:

>Copyright (c) 1992-2001 The FreeBSD Project.
>Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
>        The Regents of the University of California. All rights reserved.
>FreeBSD 4.3-RELEASE #0: Sat Apr 21 10:54:49 GMT 2001

>Timecounter "i8254"  frequency 1193182 Hz
>CPU: Pentium/P54C (166.19-MHz 586-class CPU)
>  Origin = "GenuineIntel"  Id = 0x52c  Stepping = 12
>  Features=0x1bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8>
>real memory  = 67108864 (65536K bytes)
>avail memory = 60956672 (59528K bytes)
>Preloaded elf kernel "kernel" at 0xc044d000.
>Intel Pentium detected, installing workaround for F00F bug
>md0: Malloc disk
>npx0: <math processor> on motherboard
>npx0: INT 16 interface
>pcib0: <Host to PCI bridge> on motherboard
>pci0: <PCI bus> on pcib0
>isab0: <Intel 82371SB PCI to ISA bridge> at device 7.0 on pci0
>isa0: <ISA bus> on isab0
>atapci0: <Intel PIIX3 ATA controller> port 0xe800-0xe80f at device 7.1 on
>pci0
>ata0: at 0x1f0 irq 14 on atapci0
>ata1: at 0x170 irq 15 on atapci0
>dc0: <ADMtek AN985 10/100BaseTX> port 0xe000-0xe0ff mem
>0xe6000000-0xe60003ff irq 10 at device 10.0 on pci0
>dc0: Ethernet address: 00:04:5a:45:4a:2e
>miibus0: <MII bus> on dc0
>ukphy0: <Generic IEEE 802.3u media interface> on miibus0
>ukphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
>pci0: <Matrox MGA Millennium 2064W graphics accelerator> at 12.0 irq 11
>fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
>fdc0: FIFO enabled, 8 bytes threshold
>fd0: <1440-KB 3.5" drive> on fdc0 drive 0
>atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
>atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
>kbd0 at atkbd0
>vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
>sc0: <System console> at flags 0x100 on isa0
>sc0: VGA <16 virtual consoles, flags=0x300>
>sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
>sio0: type 16550A
>sio1 at port 0x2f8-0x2ff irq 3 on isa0
>sio1: type 16550A
>ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
>ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
>plip0: <PLIP network interface> on ppbus0
>lpt0: <Printer> on ppbus0
>lpt0: Interrupt-driven port
>ppi0: <Parallel I/O> on ppbus0
>ad0: 2067MB <IBM-DAQA-32160> [4200/16/63] at ata0-master WDMA2
>acd0: CDROM <ATAPI 50X CDROM> at ata1-master using PIO4
>Mounting root from ufs:/dev/ad0s1a


 
 
 
Top

FreeBSD 4.3-RELEASE: Various applications core-dump

Post by Bill Vermilli » Wed, 06 Jun 2001 02:52:42




>I installed FreeBSD 4.3-RELEASE.
>Various software core-dumps on my machine and I have no clue why (The
>OpenSSH daemon provided with FreeBSD4.3, Apache 1.3.20, . ...). After reboot
>other or same software core-dumps, sometimes software works again till next
>reboot.
>BIOS memory-checking does not report any defective RAM.

BIOS memory check just finds if a chip is in the socket.  I can
verify that.

If nothing else go to /usr/ports/sysutils/memtest and try that.

Quote:>I have an ASUS P/I-55T2P4 motherboard, Matrox Millenium 2064W graphics
>adapter, Linksys LNE100TX NIC, IDE Harddisk and CDROM (see dmesg).

You didn't say how much memory.  I have some tests [not on BSD]
that will take almost 24 hours to run on my 512MB RAM.

You could also see if a local shop has a HW memory tester.  Those
will take about 3-4 minutes to run on a 64MB chip and are about
the best for this.

--

 
 
 
Top

FreeBSD 4.3-RELEASE: Various applications core-dump

Post by Gordon Burdi » Wed, 06 Jun 2001 03:48:31


Quote:>BIOS memory check isn't worth the bits it prints on the screen. Try it with
>better memory and see if it improves. Sig 11 indicates a hardware problem.

Sig 11 does not ALWAYS indicate a hardware problem.  Sometimes it
indicates that you need to do a (in csh):

        limit stacksize <large number here>

especially during gcc compiles of some particularly large and troublesome
source code.

However, for the problem by the original poster, I think memory hardware
really is suspect.

                                        Gordon L. Burditt

 
 
 
Top

FreeBSD 4.3-RELEASE: Various applications core-dump

Post by Jason Bourn » Fri, 08 Jun 2001 05:13:45


I am running 4.3 Release which was CVSup'd from 4.0 and 4.2 with no problems.
I am using the same MB as you, with the AMD K6-500/32MB Ram, a Promise Ultra
100 controller/WD ATA-66 HD - and it runs fine. My gut "feeling" here is look
at your RAM hardware. This looks like the kind of thing shakey memory would
produce. (Bad MB being the other most likely) Good Luck - Mine runs great!


> Hi,

> I installed FreeBSD 4.3-RELEASE.
> Various software core-dumps on my machine and I have no clue why (The
> OpenSSH daemon provided with FreeBSD4.3, Apache 1.3.20, . ...). After reboot
> other or same software core-dumps, sometimes software works again till next
> reboot.
> BIOS memory-checking does not report any defective RAM.
> I have an ASUS P/I-55T2P4 motherboard, Matrox Millenium 2064W graphics
> adapter, Linksys LNE100TX NIC, IDE Harddisk and CDROM (see dmesg).

> Anyone knows what's wrong here?

> Thanks for help,

> Tom

> ########################
> Things I found in /var/log/messages:

> pid 228 (inetd), uid 0: exited on signal 11 (core dumped)
> pid 229 (inetd), uid 0: exited on signal 11 (core dumped)
> pid 230 (inetd), uid 0: exited on signal 11 (core dumped)
> pid 231 (sshd), uid 0: exited on signal 11 (core dumped)
> .....
> dc0: TX underrun -- increasing TX threshold
> pid 372 (httpd), uid 65534: exited on signal 11
> pid 374 (httpd), uid 65534: exited on signal 11
> pid 375 (httpd), uid 65534: exited on signal 11

> ########################
> This is output from dmesg:

> Copyright (c) 1992-2001 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
>         The Regents of the University of California. All rights reserved.
> FreeBSD 4.3-RELEASE #0: Sat Apr 21 10:54:49 GMT 2001

> Timecounter "i8254"  frequency 1193182 Hz
> CPU: Pentium/P54C (166.19-MHz 586-class CPU)
>   Origin = "GenuineIntel"  Id = 0x52c  Stepping = 12
>   Features=0x1bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8>
> real memory  = 67108864 (65536K bytes)
> avail memory = 60956672 (59528K bytes)
> Preloaded elf kernel "kernel" at 0xc044d000.
> Intel Pentium detected, installing workaround for F00F bug
> md0: Malloc disk
> npx0: <math processor> on motherboard
> npx0: INT 16 interface
> pcib0: <Host to PCI bridge> on motherboard
> pci0: <PCI bus> on pcib0
> isab0: <Intel 82371SB PCI to ISA bridge> at device 7.0 on pci0
> isa0: <ISA bus> on isab0
> atapci0: <Intel PIIX3 ATA controller> port 0xe800-0xe80f at device 7.1 on
> pci0
> ata0: at 0x1f0 irq 14 on atapci0
> ata1: at 0x170 irq 15 on atapci0
> dc0: <ADMtek AN985 10/100BaseTX> port 0xe000-0xe0ff mem
> 0xe6000000-0xe60003ff irq 10 at device 10.0 on pci0
> dc0: Ethernet address: 00:04:5a:45:4a:2e
> miibus0: <MII bus> on dc0
> ukphy0: <Generic IEEE 802.3u media interface> on miibus0
> ukphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> pci0: <Matrox MGA Millennium 2064W graphics accelerator> at 12.0 irq 11
> fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
> fdc0: FIFO enabled, 8 bytes threshold
> fd0: <1440-KB 3.5" drive> on fdc0 drive 0
> atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
> atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
> kbd0 at atkbd0
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
> sc0: <System console> at flags 0x100 on isa0
> sc0: VGA <16 virtual consoles, flags=0x300>
> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
> sio0: type 16550A
> sio1 at port 0x2f8-0x2ff irq 3 on isa0
> sio1: type 16550A
> ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
> ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
> plip0: <PLIP network interface> on ppbus0
> lpt0: <Printer> on ppbus0
> lpt0: Interrupt-driven port
> ppi0: <Parallel I/O> on ppbus0
> ad0: 2067MB <IBM-DAQA-32160> [4200/16/63] at ata0-master WDMA2
> acd0: CDROM <ATAPI 50X CDROM> at ata1-master using PIO4
> Mounting root from ufs:/dev/ad0s1a

 
 
 
Top

1. Xamian on FreeBSD 4.3 || X 4.1.0 on FreeBSD 4.3

is this possible?
i downloaded the X 4.1.0 binaries and all i can run is X or XFree86 ?
its config'd and everything to 1600x1400 but i have no dri support(ati
radeon) and i have to startx with & export display then start my window
manager, there must be a better way to do this?

2. Video7 VRAM II for 3.1 XF86Config needed

3. gcc 3.2/aix 4.3 core dump on exception???

4. ATAPI CDROM *Scott Snyder* Multisession works.

5. Java program core dumps on AIX 4.3

6. Javastations, Netra servers,and mail....

7. gcc2.4.3/lib[cm]4.4.1 products dump core

8. FDISK on Hard Drives over 8 Gigs

9. g++ 2.3.3 dumps core randomly with libc.so.4.3

10. aix 4.3 and core dumps

11. How do I switch core dump format on AIX 4.3 to pre-430 style ?

12. X core dumps on FreeBSD 4.6-Release on Alpha PC164LX (really long post)

13. jdk1.1.7 core dumps on freebsd 3.1 release


All times are UTC
Board index