Very Computer

Hi there,

  I need some help especially from the PAO project people to get my
Xircom CreditCard working.. Below are the details of the card :-

Vendor: Xircom
Product Name: Xircom CreditCard Ethernet 10+Modem 33.6
Driver name: xe0
FreeBSD version: 3.5 RELEASE
PAO-RELEASE: PAO3-20000710

This is the "pccardc dumpcis" output
-----------------------------------------------------------------------
Code 136 not found
Code 136 not found
code Unknown ignored
Configuration data for card in slot 0
Tuple #1, code = 0x1 (Common memory descriptor), length = 2
    000:  00 ff
        Common memory device information:
                Device number 1, type No device, WPS = OFF
                Speed = No speed, Memory block size = reserved, 32 units
Tuple #2, code = 0x17 (Attribute memory descriptor), length = 2
    000:  00 ff
        Attribute memory device information:
                Device number 1, type No device, WPS = OFF
                Speed = No speed, Memory block size = reserved, 32 units
Tuple #3, code = 0x15 (Version 1 info), length = 52
    000:  05 00 58 69 72 63 6f 6d 00 43 72 65 64 69 74 43
    010:  61 72 64 20 45 74 68 65 72 6e 65 74 2b 4d 6f 64
    020:  65 6d 20 33 33 2e 36 00 43 45 4d 33 33 00 31 2e
    030:  30 30 00 ff
        Version = 5.0, Manuf = [Xircom], card vers = [CreditCard
Ethernet+Modem 33.6]
        Addit. info = [CEM33],[1.00]
Tuple #4, code = 0x0 (Null tuple), length = 8
    000:  96 a8 bd 00 00 00 00 00
Tuple #5, code = 0x20 (Manufacturer ID), length = 5
    000:  05 01 0c 11 44
        PCMCIA ID = 0x105, OEM ID = 0x110c
Tuple #6, code = 0x44 (Card init date), length = 4
    000:  c9 03 56 22
Tuple #7, code = 0x1a (Configuration map), length = 5
    000:  01 03 00 08 03
        Reg len = 2, config register addr = 0x800, last config = 0x3
        Registers: XX------
Tuple #8, code = 0x1b (Configuration entry), length = 22
    000:  c1 c1 bd 0f 55 4d 5d 46 e0 17 17 ea 60 f8 03 07
    010:  70 bc 8e 20 00 20
        Config index = 0x1(default)
        Interface byte = 0xc1 (I/O)  +RDY/-BSY active, wait signal
supported
        Vcc pwr:
                Nominal operating supply voltage: 5 x 1V
                Minimum operating supply voltage: 4.5 x 1V
                Maximum operating supply voltage: 5.5 x 1V
                Continuous supply current: 4 x 100mA
        Wait scale Speed = 1.2 x 10 ms
        RDY/BSY scale Speed = 1.2 x 10 ms
        Card decodes 10 address lines, full 8/16 Bit I/O
                I/O address # 1: block start = 0x3f8 block length = 0x8
                IRQ modes: Level, Pulse
                IRQs:  2 3 4 5 7 9 10 11 15
        Memory space length = 0x20
        Max twin cards = 0
        Misc attr: (Power down supported)
Tuple #9, code = 0x1b (Configuration entry), length = 7
    000:  02 08 ea 60 f8 02 07
        Config index = 0x2
        Card decodes 10 address lines, full 8/16 Bit I/O
                I/O address # 1: block start = 0x2f8 block length = 0x8
Tuple #10, code = 0x1b (Configuration entry), length = 7
    000:  23 08 ea 60 e8 03 07
        Config index = 0x23
        Card decodes 10 address lines, full 8/16 Bit I/O
                I/O address # 1: block start = 0x3e8 block length = 0x8
Tuple #11, code = 0x1b (Configuration entry), length = 7
    000:  24 08 ea 60 e8 02 07
        Config index = 0x24
        Card decodes 10 address lines, full 8/16 Bit I/O
                I/O address # 1: block start = 0x2e8 block length = 0x8
Tuple #12, code = 0x21 (Functional ID), length = 2
    000:  02 00
        Serial port/modem
Tuple #13, code = 0x22 (Functional EXT), length = 4
    000:  00 01 0f 7c
        Serial interface extension:
                16450 UART, Parity - Space,Mark,Odd,Even
                Data bit - 7bit,8bit, Stop bit - 1bit,1.5bit,2bit
Tuple #14, code = 0x22 (Functional EXT), length = 9
    000:  01 1f 3f 00 10 00 00 10 00
        Modem interface capabilities:
Tuple #15, code = 0x22 (Functional EXT), length = 12
    000:  02 00 06 3e 1f 03 03 08 03 00 00 b5
        Data modem services available:
Tuple #16, code = 0x22 (Functional EXT), length = 8
    000:  05 00 06 0f 00 02 00 b5
        Data modem interface capabilities:
        Wrong length for serial extension tuple
Tuple #17, code = 0x22 (Functional EXT), length = 8
    000:  04 00 06 0f 00 02 00 b5
Tuple #18, code = 0x21 (Functional ID), length = 2
    000:  06 00
        Network/LAN adapter
Tuple #19, code = 0x22 (Functional EXT), length = 8
    000:  04 06 00 80 c7 96 a8 bd
        Network node ID: 00 80 c7 96 a8 bd
Tuple #20, code = 0x22 (Functional EXT), length = 2
    000:  01 02
        Network technology: Ethernet
Tuple #21, code = 0x22 (Functional EXT), length = 5
    000:  02 80 96 98 00
        Network speed: 10 Mb/sec
Tuple #22, code = 0x22 (Functional EXT), length = 2
    000:  03 01
        Network media: UTP
Tuple #23, code = 0x22 (Functional EXT), length = 2
    000:  03 03
        Network media: Thin coax
Tuple #24, creturn (dpt_send_eata_command(dpt, cmd_block, cmd_busaddr,
                                      EATA_CMD_IMMEDIATE, retries, ifc,
                                      code, code2));

Quote:}

/* ===================== Priva

-----------------------------------------------------------------------

Thanks...