XF86Config for Cirrus 5428 and Smile (KFC) 14' Monitor

XF86Config for Cirrus 5428 and Smile (KFC) 14' Monitor

Post by Ari T Ko » Sat, 15 Apr 1995 04:00:00



If someone has this kind of compination I'll be glad if you could
post the XF86Config file to me. Thanks.

--
                forward forever - backward never

                 http://www.helsinki.fi/~koli/

 
 
 

XF86Config for Cirrus 5428 and Smile (KFC) 14' Monitor

Post by Wil Rodrigue » Sat, 15 Apr 1995 04:00:00


Well, I do have a clgd5428 chipset card, but I have a ctx1451 monitor.  
If you would like me to email (or post) my XF86Config file, let me know.

Wil
---


> If someone has this kind of compination I'll be glad if you could
> post the XF86Config file to me. Thanks.

> --
>            forward forever - backward never

>             http://www.helsinki.fi/~koli/

--                                       __
 <//////////////////----------......../ /..----------\\\\\\\\\\\\\\\\\\>  
 /Wil Rodriguez                      / /  (_)__  __ ____  __|The choice\

 /                                 /____/_/_//_/\_,_/ /_/\_\|Generation\
 <//////////////////----------.............----------\\\\\\\\\\\\\\\\\\>  

 
 
 

XF86Config for Cirrus 5428 and Smile (KFC) 14' Monitor

Post by Wil Rodrigue » Sat, 15 Apr 1995 04:00:00



> : ---

> YES PLEASE!  I have exactly the same setup, but I haven't had the time
> (or I've just been too lazy) to fiddle much with the XF86Config file
> yet.  My display is off-center on all modes and way too tall and narrow on
> 1024x768, so I would really appreciate this file!

> P.S.  I wonder how a 14-foot monitor would fit into any room. :)

Okay, here it is.  Make sure to read it _carefully_ and enter your
monitors specific values where indicated.

--cut here-------------------------------------------------------------
# File generated by xf86config.

#
# Copyright (c) 1994 by The XFree86 Project, Inc.
#
# Permission is hereby granted, free of charge, to any person obtaining a
# copy of this software and associated documentation files (the "Software"),
# to deal in the Software without restriction, including without limitation
# the rights to use, copy, modify, merge, publish, distribute, sublicense,
# and/or sell copies of the Software, and to permit persons to whom the
# Software is furnished to do so, subject to the following conditions:
#
# The above copyright notice and this permission notice shall be included in
# all copies or substantial portions of the Software.
#
# THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
# IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
# FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.  IN NO EVENT SHALL
# THE XFREE86 PROJECT BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
# WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF
# OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
# SOFTWARE.
#
# Except as contained in this notice, the name of the XFree86 Project shall
# not be used in advertising or otherwise to promote the sale, use or other
# dealings in this Software without prior written authorization from the
# XFree86 Project.
#

# **********************************************************************
# Refer to the XF86Config(4/5) man page for details about the format of
# this file.
# **********************************************************************

# **********************************************************************
# Files section.  This allows default font and rgb paths to be set
# **********************************************************************

Section "Files"

    RgbPath     "/usr/X11R6/lib/X11/rgb"

# Multiple FontPath entries are allowed (which are concatenated together),
# as well as specifying multiple comma-separated entries in one FontPath
# command (or a combination of both methods)

# I have all of these fonts installed, comment out the ones you don't have
    FontPath    "/usr/X11R6/lib/X11/fonts/100dpi/"
    FontPath    "/usr/X11R6/lib/X11/fonts/75dpi/"
    FontPath    "/usr/X11R6/lib/X11/fonts/Type1/"
    FontPath    "/usr/X11R6/lib/X11/fonts/Speedo/"
    FontPath    "/usr/X11R6/lib/X11/fonts/misc/"

EndSection

# **********************************************************************
# Server flags section.
# **********************************************************************

Section "ServerFlags"

# Uncomment this to disable the <Crtl><Alt><BS> server abort sequence
#    DontZap

EndSection

# **********************************************************************
# Keyboard section
# **********************************************************************

Section "Keyboard"

    Protocol    "Standard"
    AutoRepeat  500 5
    ServerNumLock

# To set the LeftAlt to Meta, RightAlt key to ModeShift,
# RightCtl key to Compose, and ScrollLock key to ModeLock:

#    LeftAlt     Meta
#    RightAlt    ModeShift
#    RightCtl    Compose
#    ScrollLock  ModeLock

EndSection

# **********************************************************************
# Pointer section
# **********************************************************************

# I have a Microsucks compatible mouse
Section "Pointer"
    Protocol    "Microsoft"
    Device      "/dev/mouse"
    ChordMiddle
EndSection

# **********************************************************************
# Monitor section
# **********************************************************************

# Any number of monitor sections may be present

# You can change these...
Section "Monitor"

    Identifier  "My Monitor"
    VendorName  "CTX"
    ModelName   "1451"

# Bandwidth is in MHz unless units are specified
# HorizSync is in kHz unless units are specified.

# WARNING: THESE VALUES ARE FOR _MY_ MONITOR, CHECK THEM AGAINST YOURS!!!

    HorizSync  30-50         # my monitor's manual says so

# VertRefresh is in Hz unless units are specified.

    VertRefresh 50-90        # straight from the manual

# All of these modelines work for me.  I did hacked them to center the image


Modeline "640x480"     25.175 640  664  760  800   480  491  493  525


Modeline "800x600"     40     800  848  968 1048   600  601  605  628 +hsync +vsync


Modeline "1024x768"    65    1024 1048 1176 1326   768  771  777  806 -hsync -vsync

EndSection

# **********************************************************************
# Graphics device section
# **********************************************************************

# Any number of graphics device sections may be present

# Standard VGA Device:

Section "Device"
    Identifier  "Generic SVGA"
    VendorName  "Unknown"
    BoardName   "Unknown"
    Chipset     "generic"
EndSection

# Device configured by xf86config:

# you can change these...

Section "Device"
    Identifier  "My Video Card"
    VendorName  "Genoa"
    BoardName   "8500vl"
    VideoRam    1024

# NOTE: These are the dot-clocks for the clgd5428, DON'T CHANGE THESE!!!

Clocks 25.23 28.32 41.16 36.08 31.50 39.99 45.08 49.87 64.98 72.16 75.00 80.01
EndSection

# **********************************************************************
# Screen sections
# **********************************************************************

# The Colour SVGA server

# You might want to keep the noaccel function in, without it the system
# either hanged or wouldn't redraw screens properly.

Section "Screen"
    Driver      "svga"
#    Device      "Generic VGA"
    Device      "My Video Card"
    Monitor     "My Monitor"
    Subsection "Display"
         Depth       8
         Modes       "1024x768" "800x600" "640x480"
         ViewPort    0 0
         Virtual     1024 768
         Option "noaccel"
    EndSubsection
EndSection

--cut here----------------------------------------------------------------

Good luck,

Wil

--                                       __
 <//////////////////----------......../ /..----------\\\\\\\\\\\\\\\\\\>  
 /Wil Rodriguez                      / /  (_)__  __ ____  __|The choice\

 /                                 /____/_/_//_/\_,_/ /_/\_\|Generation\
 <//////////////////----------.............----------\\\\\\\\\\\\\\\\\\>  

 
 
 

1. CIrrus 5428 + 14" VGA

HELP!!!
        I have installed the slackware version of linux on my 486 and I
can't get X11 to work. I have had it on my machine for about 2 months now
without getting it to work. SO if I cant get it so work soon I will repartition
my hard drive and I will have to go linuxless.

I have a cirrus logic 5428 graphics card and a s/vga monitor. I bought it
as a vga but it can handle 800*600 ver flickery (sort of) anyway the make of
the monitor is CTX??? Can anyone help me please!!!>?!?!?!?

                        Ken f

2. can't stop a kernel process

3. XF86Config problems, Cirrus 5428, PS/1 HiFunction MS at 16 bpp

4. XDM weird problem

5. Xconfig file for Cirrus Logic 5428 chip/ViewSonic 6e monitor.

6. ANNOUNCE: GTK+XFce 3.0.2 now released

7. XF86Free config file needed for Cirrus logic CL-5428 w/1M and NEC XV15+ monitor

8. Problem (?!) with Wisecom 56K Modem.

9. ICL Monitor - ValuePlus & Cirrus Logic 5428

10. Xconfig for Cirrus 5428 and Generic Monitor.

11. Cirrus Logic 5428 and CMS 1561: Display `smeared'

12. X with Cirrus-logic GD5426 on AAMAZING 14" monitor?

13. HELP!!! ModeLine Options of XF86Config for KFC monitor