by
I have Red Hat 5.2 and a VideoExcel i740 8MB AGP video card on a Celeron
300A system. I have installed the XBF-i740-glibc-1.0.0-1.i386.rpm
package and then made the link to
lrwxrwxrwx 1 root root 23 Mar 16 23:08 /etc/X11/X ->
/usr/X11R6/bin/XBF_i740*
I then installed xf86config-glibc-1.0.0.i386.tgz in the proper
directory. I then used xf86config to set up my new server for my card.
I made all of the selections required and the card that I picked from
the list was the Intel i740 (generic). I then try startx but I only get
an error message:
Config Error: /etc/XF86Config:534
ViewPort 0 0
^^^^^^^^^
Mode name expected
_X11TransSocketUNIXConnect: Can't connect: errno = 111
giving up.^M
xinit: Connection refused (errno 111): unable to connect to X server^M
xinit: No such process (errno 3): Server error.
I have included my XF86Config file and the output of attempting startx,
as attachments. To me, the key error seems to be the
ViewPort 0 0
on line 534 of the XF86Config file, but I now almost nothing about X11.
Thank you for your help.
[
startx.output 2K ]
XBF_i740 Version 1.0.0 / X Window System
(protocol Version 11, revision 0, vendor release 6300)
Release Date: December 21 1998
If the server is older than 6-12 months, or if your card is newer
than the above date, look for a newer version before reporting
problems. Please see ftp://ftp.redhat.com/pub/XBF/ for the latest
i740 server.
Please report any problems to "xbf_supp...@redhat.com".
Operating System: Linux 2.0.35 i686 [ELF]
Configured drivers:
SVGA: server for SVGA graphics adaptors (Patchlevel 0):
i740, i740_pci, generic
(using VT number 7)
XF86Config: /etc/XF86Config
(**) stands for supplied, (--) stands for probed/default values
(**) XKB: keymap: "xfree86(us)" (overrides other XKB settings)
(**) Mouse: type: PS/2, device: /dev/mouse, buttons: 3
(**) SVGA: Graphics device ID: "Video Excell i740"
(**) SVGA: Monitor ID: "TVM AS6S"
(--) SVGA: Mode "1024x768" needs hsync freq of 70.24 kHz. Deleted.
(--) SVGA: Mode "1152x864" needs hsync freq of 70.88 kHz. Deleted.
(--) SVGA: Mode "1280x1024" needs hsync freq of 74.59 kHz. Deleted.
(--) SVGA: Mode "1600x1200" needs hsync freq of 75.00 kHz. Deleted.
(--) SVGA: Mode "1152x864" needs hsync freq of 76.01 kHz. Deleted.
(--) SVGA: Mode "1280x1024" needs hsync freq of 78.86 kHz. Deleted.
(--) SVGA: Mode "1024x768" needs hsync freq of 80.21 kHz. Deleted.
(--) SVGA: Mode "1280x1024" needs hsync freq of 81.13 kHz. Deleted.
(--) SVGA: Mode "1600x1200" needs hsync freq of 87.50 kHz. Deleted.
(--) SVGA: Mode "1152x864" needs hsync freq of 89.62 kHz. Deleted.
(--) SVGA: Mode "1280x1024" needs hsync freq of 91.15 kHz. Deleted.
(--) SVGA: Mode "1600x1200" needs hsync freq of 93.75 kHz. Deleted.
(--) SVGA: Mode "1600x1200" needs hsync freq of 105.77 kHz. Deleted.
(--) SVGA: Mode "1280x1024" needs hsync freq of 107.16 kHz. Deleted.
(--) SVGA: Mode "1800X1440" needs hsync freq of 96.15 kHz. Deleted.
(--) SVGA: Mode "1800X1440" needs hsync freq of 104.52 kHz. Deleted.
Config Error: /etc/XF86Config:534
ViewPort 0 0
^^^^^^^^^
Mode name expected
_X11TransSocketUNIXConnect: Can't connect: errno = 111
giving up.
xinit: Connection refused (errno 111): unable to connect to X server
xinit: No such process (errno 3): Server error.
[
XF86Conf 19K ]
# File generated by xf86config.
#
# Copyright (c) 1995 by The XFree86 Project, Inc.
#
# Permission is hereby granted, free of charge, to any person obtaining a
# copy of this software and associated documentation files (the "Software"),
# to deal in the Software without restriction, including without limitation
# the rights to use, copy, modify, merge, publish, distribute, sublicense,
# and/or sell copies of the Software, and to permit persons to whom the
# Software is furnished to do so, subject to the following conditions:
#
# The above copyright notice and this permission notice shall be included in
# all copies or substantial portions of the Software.
#
# THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
# IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
# FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
# THE XFREE86 PROJECT BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
# WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF
# OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
# SOFTWARE.
#
# Except as contained in this notice, the name of the XFree86 Project shall
# not be used in advertising or otherwise to promote the sale, use or other
# dealings in this Software without prior written authorization from the
# XFree86 Project.
#
# **********************************************************************
# Refer to the XF86Config(4/5) man page for details about the format of
# this file.
# **********************************************************************
# **********************************************************************
# Files section. This allows default font and rgb paths to be set
# **********************************************************************
Section "Files"
# The location of the RGB database. Note, this is the name of the
# file minus the extension (like ".txt" or ".db"). There is normally
# no need to change the default.
RgbPath "/usr/X11R6/lib/X11/rgb"
# Multiple FontPath entries are allowed (which are concatenated together),
# as well as specifying multiple comma-separated entries in one FontPath
# command (or a combination of both methods)
#
# If you don't have a floating point coprocessor and emacs, Mosaic or other
# programs take long to start up, try moving the Type1 and Speedo directory
# to the end of this list (or comment them out).
#
# FontPath "/usr/X11R6/lib/X11/fonts/local/"
FontPath "/usr/X11R6/lib/X11/fonts/misc/"
FontPath "/usr/X11R6/lib/X11/fonts/75dpi/:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/100dpi/:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/Type1/"
FontPath "/usr/X11R6/lib/X11/fonts/Speedo/"
FontPath "/usr/X11R6/lib/X11/fonts/75dpi/"
FontPath "/usr/X11R6/lib/X11/fonts/100dpi/"
# For OSs that support Dynamically loaded modules, ModulePath can be
# used to set a search path for the modules. This is currently supported
# for Linux ELF, FreeBSD 2.x and NetBSD 1.x. The default path is shown
# here.
# ModulePath "/usr/X11R6/lib/modules"
EndSection
# **********************************************************************
# Module section -- this is an optional section which is used to specify
# which dynamically loadable modules to load. Dynamically loadable
# modules are currently supported only for Linux ELF, FreeBSD 2.x
# and NetBSD 1.x. Currently, dynamically loadable modules are used
# only for some extended input (XInput) device drivers.
# **********************************************************************
#
# Section "Module"
#
# This loads the module for the Joystick driver
#
# Load "xf86Jstk.so"
#
# EndSection
# **********************************************************************
# Server flags section.
# **********************************************************************
Section "ServerFlags"
# Uncomment this to cause a core dump at the spot where a signal is
# received. This may leave the console in an unusable state, but may
# provide a better stack trace in the core dump to aid in debugging
# NoTrapSignals
# Uncomment this to disable the <Crtl><Alt><BS> server abort sequence
# This allows clients to receive this key event.
# DontZap
# Uncomment this to disable the <Crtl><Alt><KP_+>/<KP_-> mode switching
# sequences. This allows clients to receive these key events.
# DontZoom
# Uncomment this to disable tuning with the xvidtune client. With
# it the client can still run and fetch card and monitor attributes,
# but it will not be allowed to change them. If it tries it will
# receive a protocol error.
# DisableVidModeExtension
# Uncomment this to enable the use of a non-local xvidtune client.
# AllowNonLocalXvidtune
# Uncomment this to disable dynamically modifying the input device
# (mouse and keyboard) settings.
# DisableModInDev
# Uncomment this to enable the use of a non-local client to
# change the keyboard or mouse settings (currently only xset).
# AllowNonLocalModInDev
EndSection
# **********************************************************************
# Input devices
# **********************************************************************
# **********************************************************************
# Keyboard section
# **********************************************************************
Section "Keyboard"
Protocol "Standard"
# when using XQUEUE, comment out the above line, and uncomment the
# following line
# Protocol "Xqueue"
AutoRepeat 500 5
# Let the server do the NumLock processing. This should only be required
# when using pre-R6 clients
# ServerNumLock
# Specify which keyboard LEDs can be user-controlled (eg, with xset(1))
# Xleds 1 2 3
# To set the LeftAlt to Meta, RightAlt key to ModeShift,
# RightCtl key to Compose, and ScrollLock key to ModeLock:
# LeftAlt Meta
# RightAlt ModeShift
# RightCtl Compose
# ScrollLock ModeLock
# To disable the XKEYBOARD extension, uncomment XkbDisable.
# XkbDisable
# To customise the XKB settings to suit your keyboard, modify the
# lines below (which are the defaults). For example, for a non-U.S.
# keyboard, you will probably want to use:
# XkbModel "pc102"
# If you have a US Microsoft Natural keyboard, you can use:
# XkbModel "microsoft"
#
# Then to change the language, change the Layout setting.
# For example, a german layout can be obtained with:
# XkbLayout "de"
# or:
# XkbLayout "de"
# XkbVariant "nodeadkeys"
#
# If you'd like to switch the positions of your capslock and
# control keys, use:
# XkbOptions "ctrl:swapcaps"
# These are the default XKB settings for XFree86
# XkbRules "xfree86"
# XkbModel "pc101"
# XkbLayout "us"
# XkbVariant ""
# XkbOptions ""
XkbKeymap "xfree86(us)"
EndSection
# **********************************************************************
# Pointer section
# **********************************************************************
Section "Pointer"
Protocol "PS/2"
Device "/dev/mouse"
# When using XQUEUE, comment out the above two lines, and uncomment
# the following line.
# Protocol "Xqueue"
# Baudrate and SampleRate are only for some Logitech mice
# or for the AceCad tablets which require 9600 baud
# BaudRate 9600
# SampleRate 150
# Emulate3Buttons is an option for 2-button Microsoft mice
# Emulate3Timeout is the timeout in milliseconds (default is 50ms)
# Emulate3Buttons
# Emulate3Timeout 50
# ChordMiddle is an option for some 3-button Logitech mice
# ChordMiddle
EndSection
# **********************************************************************
# Xinput section -- this is optional and is required only if you
# are using extended input devices. This is for example only. Refer
# to the XF86Config man page for a description of the options.
# **********************************************************************
#
# Section "Xinput"
# SubSection "WacomStylus"
# Port "/dev/ttyS1"
# DeviceName "Wacom"
# EndSubSection
# SubSection "WacomCursor"
# Port "/dev/ttyS1"
# EndSubSection
# SubSection "WacomEraser"
# Port "/dev/ttyS1"
# EndSubSection
#
# SubSection "Elographics"
# Port "/dev/ttyS1"
# DeviceName "Elo"
# MinimumXPosition 300
# MaximumXPosition 3500
# MinimumYPosition 300
# MaximumYPosition 3500
# Screen 0
# UntouchDelay 10
# ReportDelay 10
# EndSubSection
#
# SubSection "Joystick"
# Port "/dev/joy0"
# DeviceName "Joystick"
# TimeOut 10
# MinimumXPosition 100
# MaximumXPosition 1300
# MinimumYPosition 100
# MaximumYPosition 1100
# # CenterX 700
# # CenterY 600
# Delta 20
# EndSubSection
#
# The Mouse Subsection contains the same type of entries as the
# standard Pointer Section (see above), with the addition of the
# DeviceName entry.
#
# SubSection "Mouse"
# Port "/dev/mouse2"
# DeviceName "Second Mouse"
# Protocol "Logitech"
# EndSubSection
# EndSection
# **********************************************************************
# Monitor section
# **********************************************************************
# Any number of monitor sections may be present
Section "Monitor"
Identifier "TVM AS6S"
VendorName "TVM"
ModelName "AS6S"
# HorizSync is in kHz unless units are specified.
# HorizSync may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.
HorizSync 30-70
# HorizSync 30-64 # multisync
# HorizSync 31.5, 35.2 # multiple fixed sync frequencies
# HorizSync 15-25, 30-50 # multiple ranges of sync frequencies
# ...
read more »