by OK I have RH 5.1 installed on my system.
config is as follows:
ASUS P/I P55T2P4 mother board, with 64 MB of EDO dram
BT958 scsi controller
IBM Dcas 34330 F/W scsi drive
Conner 1.0 Gig Scsi drive
Toshiba cd rom
Matrox Millenium graphics card.
I scored a memory test from the net which you load on to floppy, reboot
your system
and run this test in a low-level mode. No errors
I have been having problems like this for about a year. Up until I
replaced the
BT958 I was not suspecting my motherboard. Maybe that is the next thing
to be replaced. Does anyone have any idea what these errors are pointing
to
in terms of hw failure
I just replaced the BT958, the cables are new also. I have been getting
a lot of
these errors:
EXT2-fs error (device 08:02): ext2_readdir: directory #75170 contains a
hole at
offset 2048
EXT2-fs error (device 08:02): ext2_readdir: directory #75170 contains a
hole at
offset 3072
EXT2-fs error (device 08:02): ext2_readdir: directory #75170 contains a
hole at
offset 4096
EXT2-fs error (device 08:02): ext2_readdir: directory #75170 contains a
hole at
offset 5120
EXT2-fs error (device 08:02): ext2_readdir: directory #75170 contains a
hole at
offset 6144
SCSI disk error : host 0 channel 0 id 0 lun 0 return code = 28000002
extra data not valid Current error sd08:02: sense key Illegal Request
Additional sense indicates Invalid field in cdb
scsidisk I/O error: dev 08:02, sector 327720, absolute sector 536616
scsi : aborting command due to timeout : pid 13085, scsi0, channel 0, id
0, lun
0 Write (6) 03 70 10 02 00
scsi0: Aborting CCB #13098 to Target 0
scsi : aborting command due to timeout : pid 13086, scsi0, channel 0, id
0, lun
0 Write (6) 03 f0 2a 04 00
scsi0: Aborting CCB #13099 to Target 0
scsi : aborting command due to timeout : pid 13087, scsi0, channel 0, id
0, lun
0 Write (6) 04 70 16 02 00
scsi0: Aborting CCB #13100 to Target 0
scsi : aborting command due to timeout : pid 13088, scsi0, channel 0, id
0, lun
0 <4>scsi0: CCB #13098 to Target 0 Aborted
Write (6) 04 70 4c 02 00
scsi0: Aborting CCB #13101 to Target 0
scsi : aborting command due to timeout : pid 13089, scsi0, channel 0, id
0, lun
0 Write (6) 04 70 52 04 00
scsi0: CCB #13099 to Target 0 Aborted
scsi0: Aborting CCB #13102 to Target 0
scsi : aborting command due to timeout : pid 13090, scsi0, channel 0, id
0, lun
0 <4>scsi0: CCB #13100 to Target 0 Aborted
Write (6) 05 30 1a 02 00
scsi0: Aborting CCB #13103 to Target 0
scsi : aborting command due to timeout : pid 13091, scsi0, channel 0, id
0, lun
0 Write (6) 05 70 26 02 00
scsi0: CCB #13101 to Target 0 Aborted
scsi0: Aborting CCB #13104 to Target 0
scsi : aborting command due to timeout : pid 13092, scsi0, channel 0, id
0, lun
0 Write (6) 05 f0 20 02 00
scsi0: Aborting CCB #13105 to Target 0
scsi : aborting command due to timeout : pid 13093, scsi0, channel 0, id
0, lun
0 Write (6) 06 30 18 02 00
scsi0: Aborting CCB #13106 to Target 0
scsi : aborting command due to timeout : pid 13094, scsi0, channel 0, id
0, lun
0 <4>scsi0: CCB #13102 to Target 0 Aborted
Write (6) 06 30 24 02 00