Adaptec AVA1505 SCSI controller and HP6000i DAT tape drive

Adaptec AVA1505 SCSI controller and HP6000i DAT tape drive

Post by Chris Webe » Wed, 19 Jun 1996 04:00:00



I have the above listed items and I am unable to get the AHA152x
driver to pick up the HP drive.  Thanks to the help of many the
controller is being recognized but when the LUNS are being probed the
tape drive is not found.  Below is a listing of the messages that appear
when probing:

Are there any suggestions???  Thank you.

Chris
----------------------------------------------------------------------

Jun 10 16:17:12 pepe kernel: waiting: SCSISEQ (); SCSISIG (DATA OUT);
INTSTAT (h
i); SSTAT (BUSFREE ); SSTAT (BUSFREE ); SXFRCTL0 (CH1 ); SIGNAL ();
SELID (00),
SSTAT2 (SEMPTY ); SFCNT (0); SCSICNT (0), OFFCNT(0), SSTAT4 ();
DMACNTRL0 (16BIT
 PIO READ INTEN ); DMASTAT (DFIFOEMP )
Jun 10 16:17:12 pepe kernel: enabled interrupts (ENBUSFREE )
Jun 10 16:17:12 pepe kernel: scsi : aborting command due to timeout :
pid 2, scs
i0, channel 0, id 2, lun 0 Test Unit Ready 00 00 00 00 00
Jun 10 16:17:12 pepe kernel: aha152x: abort(), SCpnt=0x00092018, QUEUE
STATUS:
Jun 10 16:17:12 pepe kernel: issue_SC:
Jun 10 16:17:12 pepe kernel: 0x00092018: target=2; lun=0; cmnd=(Test
Unit Ready
00 00 00 00 00
Jun 10 16:17:12 pepe kernel: ); residual=256; buffers=0; phase |not
issued|; nex
t=0x00000000
Jun 10 16:17:12 pepe kernel: current_SC:
Jun 10 16:17:12 pepe kernel: none
Jun 10 16:17:12 pepe kernel: disconnected_SC:
Jun 10 16:17:12 pepe kernel:
Jun 10 16:17:12 pepe kernel: waiting: SCSISEQ (); SCSISIG (DATA OUT);
INTSTAT (h
i); SSTAT (BUSFREE ); SSTAT (BUSFREE ); SXFRCTL0 (CH1 ); SIGNAL ();
SELID (00),
SSTAT2 (SEMPTY ); SFCNT (0); SCSICNT (0), OFFCNT(0), SSTAT4 ();
DMACNTRL0 (16BIT
 PIO READ INTEN ); DMASTAT (DFIFOEMP )
Jun 10 16:17:12 pepe kernel: enabled interrupts (ENBUSFREE )
Jun 10 16:17:12 pepe kernel: scsi : aborting command due to timeout :
pid 2, scs
i0, channel 0, id 2, lun 0 Test Unit Ready 00 00 00 00 00
Jun 10 16:17:12 pepe kernel: aha152x: abort(), SCpnt=0x00092018, QUEUE
STATUS:
Jun 10 16:17:12 pepe kernel: issue_SC:
Jun 10 16:17:12 pepe kernel: 0x00092018: target=2; lun=0; cmnd=(Test
Unit Ready
00 00 00 00 00
Jun 10 16:17:12 pepe kernel: ); residual=256; buffers=0; phase |not
issued|; nex
t=0x00000000
Jun 10 16:17:12 pepe kernel: current_SC:
Jun 10 16:17:12 pepe kernel: none
Jun 10 16:17:12 pepe kernel: disconnected_SC:
Jun 10 16:17:12 pepe kernel:
Jun 10 16:17:12 pepe kernel: waiting: SCSISEQ (); SCSISIG (DATA OUT);
INTSTAT (h
i); SSTAT (BUSFREE ); SSTAT (BUSFREE ); SXFRCTL0 (CH1 ); SIGNAL ();
SELID (00),
SSTAT2 (SEMPTY ); SFCNT (0); SCSICNT (0), OFFCNT(0), SSTAT4 ();
DMACNTRL0 (16BIT
 PIO READ INTEN ); DMASTAT (DFIFOEMP )
Jun 10 16:17:12 pepe kernel: enabled interrupts (ENBUSFREE )
Jun 10 16:17:12 pepe kernel: scsi : aborting command due to timeout :
pid 3, scs

--
====================================================================
Chris Weber                               Phone: 614/847-6161
Scherers Communications Group             Fax:   614/847-2395

Worthington, Ohio 43085
====================================================================

 
 
 

1. how do you install adaptec ava1505 scsi controller

What is the process to install a scsi controller in RedHat 7.1?
I have a workstation loaded and operational. I tried installing a SCSI
controller (i/o=0x140, Int=10) to host a Sony CDROM burner with no
success.The parameters are jumpered on the board. I tried installing
the card from a complete new linux installation and also tried
installing the card after the OS is up and running. No success either
way. The card does not appear to be detected. RedHat indicates the
card is supported using aha152x driver.

The card works. It now hosts a SCSI scanner and CDROM burner in a
windows box.  If I can  successfully install the card I hope to
eliminate that windows box.

I was hoping someone had some experience with this type of
installation and might offer a stepped process to success.

Sean

2. Cannon BJC-610 problems!

3. Adaptec AVA1505 SCSI controller

4. Problems with NetGear FA310TX on Redhat 8

5. ADAPTEC 1542B DOES NOT RECOGNIZE SCSI TAPE DRIVE AND SCSI TAPE ?

6. Sound with IBM ThinkPad 570

7. DAT tapes vs. non-DAT tapes ( SCSI )

8. Seeking suggestions on encryption algorithm

9. DAT TAPE DRIVES: Wangtek can't read HP DAT tapes

10. can't erase tape drive: was DAT drive kill SCSI

11. Can PAS16 SCSI drive SCSI DAT tape?

12. 2GB DAT tape funktioning with a NCR 53c815 SCSI Controller

13. Adaptec 2920 (fdomain) SCSI driven tape drive timeouts