Very Computer

Hi,
I got a HP7100+ CD-Writer on parallel port. I usr the pg driver with
epat
protocol, scsi emulation,  at boot time, I got this:

hdc: HITACHI CDR-8130, ATAPI CDROM drive - enabling SCSI emulation
ATAPI overlap supported: No
hdd: IOMEGA ZIP 100 ATAPI, ATAPI FLOPPY drive - enabling SCSI emulation
ATAPI overlap supported: No
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
paride: epat registered as protocol 0
pg: pg version 1.01s, major 97
pg0: epat 1.01, Shuttle EPAT chip c6 at 0x378, mode 1 (5/3), delay 1
pg0: HP CD-Writer+ 7100, slave
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
scsi : 1 host.
  Vendor: HITACHI   Model: CDR-8130          Rev: 0021
  Type:   CD-ROM                             ANSI SCSI revision: 02
  Vendor: IOMEGA    Model: ZIP 100           Rev: 23.D
  Type:   Direct-Access                      ANSI SCSI revision: 00  
scsi : detected total.  

When I try cdrecord -scanbus, I got:

Quote:>cdrecord -scanbus

Cdrecord release 1.6 Copyright (C) 1995-1998 J?rg Schilling
scsibus0:
                  0) 'HP      ' 'CD-Writer+ 7100 ' '1.00' Removable
CD-ROM

As it is recognize as a Removable CD-ROM, I can't write on it !

An other test:

Quote:>cdrecord -checkdrive dev=1,0,0

Cdrecord release 1.6 Copyright (C) 1995-1998 J?rg Schilling
scsidev: '1,0,0'
scsibus: 1 target: 0 lun: 0
Device type    : Removable CD-ROM
Version        : 0
Response Format: 1
Vendor_info    : 'HP      '
Identifikation : 'CD-Writer+ 7100 '
Revision       : '1.00'
Device seems to be: Generic mmc CD-RW.
Using generic SCSI-3/mmc CD-R driver (mmc_cdr).
Driver flags   : SWABAUDIO
-------------------------------
If I try to write something, I get:

Quote:>cdrecord -v -speed=2 dev=0,0,0 binary-i386.raw

Cdrecord release 1.6 Copyright (C) 1995-1998 J?rg Schilling
TOC Type: 1 = CD-ROM
cdrecord: Function not implemented. shmget failed
-------------------------------

Quote:>cat /proc/devices

Character devices:
 1 mem
 2 pty
 3 ttyp
 4 ttyp
 5 cua
 7 vcs
10 misc
21 sg
97 pg

Block devices:
 2 fd
 3 ide0
 7 loop
22 ide1  
---------------------------------------

Quote:>cat /proc/ioports

0000-001f : dma1
0020-003f : pic1
0040-005f : timer
0060-006f : keyboard
0080-009f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : npu
0170-0177 : ide1
01f0-01f7 : ide0
02f8-02ff : serial(set)
0376-0376 : ide1
0378-037f : pg0
03c0-03df : vga+
03f0-03f5 : floppy
03f6-03f6 : ide0
03f7-03f7 : floppy DIR
03f8-03ff : serial(set)
ff00-ff1f : 3c905 Boomerang 100baseTx
ffa0-ffa7 : IDE DMA
ffa8-ffaf : IDE DMA

Any Idea ??????? What's wrong ?
--
      Laurent GIRAUD
      Centre for Systems Engineering and Applied Mechanics (CESAME)
      Universite catholique de Louvain
      Batiment Euler -- Av. Georges Lemaitre, 4
      B-1348 Louvain-la-Neuve -- Belgium
      Tel : +32-10-47 8055
      Fax : +32-10-47 2180