Bravo 16P PnP Sound card

Bravo 16P PnP Sound card

Post by DB » Mon, 06 Jan 1997 04:00:00



I have the avouve sound card, and it works OK under Win95. To get it
working under Linux, I have downloaded the isapnptools. I got it
compiled and installed, and ran pnpdump. The results are attached below.

The problem is that I have no idea what to uncomment. I wrote down the
parameters for the card under Win95. They also appear below. Can anyone
help me figure how to modify this isapnp.conf ?

Win95 Settings:
---------------
I/O 0608-060B    IRQ 10    DMA 00
    0390-039B                  06
    0240-024F
    0E0D-0E0F

and for MPU-401, I/O 0330-0331

-----------------------------

Here is my virgin isapnp.conf:
-----------------------------

# Trying port address 0203
# Board 1 has serial identifier 74 ff ff ff ff 31 09 14 3e

# (DEBUG)
(READPORT 0x0203)
(ISOLATE)
(IDENTIFY *)

# Card 1: (serial identifier 74 ff ff ff ff 31 09 14 3e)
# OPT0931 Serial No -1 [checksum 74]
# Version 1.0, Vendor version 0.0
# ANSI string -->AT931 Audio 16<--
#
# Logical device id OPTffff
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be
changed if required
# Don't forget to uncomment the activate (ACT Y) when happy

(CONFIGURE OPT0931/-1 (LD 0
#     ANSI string -->Aux Device<--
# (ACT Y)
))
#
# Logical device id OPT9310
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be
changed if required
# Don't forget to uncomment the activate (ACT Y) when happy

(CONFIGURE OPT0931/-1 (LD 1
#     ANSI string -->Audio<--

# Multiple choice time, choose one only !

#     Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0534
#             Maximum IO base address 0x0608
#             IO base alignment 212 bytes
#             Number of IO addresses required: 4
# (IO 0 (BASE 0x0534))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0380
#             Maximum IO base address 0x03f0
#             IO base alignment 16 bytes
#             Number of IO addresses required: 12
# (IO 1 (BASE 0x0380))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0240
#             IO base alignment 32 bytes
#             Number of IO addresses required: 16
# (IO 2 (BASE 0x0220))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0e0d
#             Maximum IO base address 0x0e0d
#             IO base alignment 1 bytes
#             Number of IO addresses required: 3
# (IO 3 (BASE 0x0e0d))
#       IRQ 5, 7 or 10.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
#       First DMA channel 0.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed type F
# (DMA 0 (CHANNEL 0))
#       Next DMA channel 0, 1, 3, 5 or 6.
#             8 & 16 bit DMA
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may execute in count by word mode
#             DMA channel speed type F
# (DMA 1 (CHANNEL 0))

#       Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0534
#             Maximum IO base address 0x0608
#             IO base alignment 212 bytes
#             Number of IO addresses required: 4
# (IO 0 (BASE 0x0534))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0380
#             Maximum IO base address 0x03f0
#             IO base alignment 16 bytes
#             Number of IO addresses required: 12
# (IO 1 (BASE 0x0380))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0240
#             IO base alignment 32 bytes
#             Number of IO addresses required: 16
# (IO 2 (BASE 0x0220))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0e8d
#             Maximum IO base address 0x0e8d
#             IO base alignment 1 bytes
#             Number of IO addresses required: 3
# (IO 3 (BASE 0x0e8d))
#       IRQ 5, 7 or 10.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
#       First DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed type F
# (DMA 0 (CHANNEL 0))
#       Next DMA channel 0, 1, 3, 5 or 6.
#             8 & 16 bit DMA
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may execute in count by word mode
#             DMA channel speed type F
# (DMA 1 (CHANNEL 0))

#       Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0534
#             Maximum IO base address 0x0ff0
#             IO base alignment 4 bytes
#             Number of IO addresses required: 4
# (IO 0 (BASE 0x0534))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0380
#             Maximum IO base address 0x03f0
#             IO base alignment 16 bytes
#             Number of IO addresses required: 12
# (IO 1 (BASE 0x0380))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0240
#             IO base alignment 32 bytes
#             Number of IO addresses required: 16
# (IO 2 (BASE 0x0220))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0e8d
#             Maximum IO base address 0x0e8d
#             IO base alignment 1 bytes
#             Number of IO addresses required: 3
# (IO 3 (BASE 0x0e8d))
#       IRQ 5, 7 or 10.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
#       First DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed type F
# (DMA 0 (CHANNEL 0))
#       Next DMA channel 0, 1, 3, 5 or 6.
#             8 & 16 bit DMA
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may execute in count by word mode
#             DMA channel speed type F
# (DMA 1 (CHANNEL 0))

#       Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0534
#             Maximum IO base address 0x0ff0
#             IO base alignment 4 bytes
#             Number of IO addresses required: 4
# (IO 0 (BASE 0x0534))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0380
#             Maximum IO base address 0x03f0
#             IO base alignment 16 bytes
#             Number of IO addresses required: 12
# (IO 1 (BASE 0x0380))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0240
#             IO base alignment 32 bytes
#             Number of IO addresses required: 16
# (IO 2 (BASE 0x0220))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0e0d
#             Maximum IO base address 0x0ffd
#             IO base alignment 16 bytes
#             Number of IO addresses required: 3
# (IO 3 (BASE 0x0e0d))
#       IRQ 5, 7, 9, 10 or 11.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
#       First DMA channel 0, 1, 3, 5 or 6.
#             8 & 16 bit DMA
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may execute in count by word mode
#             DMA channel speed type F
# (DMA 0 (CHANNEL 0))
#       Next DMA channel 0, 1, 3, 5 or 6.
#             8 & 16 bit DMA
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may execute in count by word mode
#             DMA channel speed type F
# (DMA 1 (CHANNEL 0))

#       Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0534
#             Maximum IO base address 0x0ff0
#             IO base alignment 4 bytes
#             Number of IO addresses required: 4
# (IO 0 (BASE 0x0534))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0380
#             Maximum IO base address 0x03f0
#             IO base alignment 16 bytes
#             Number of IO addresses required: 12
# (IO 1 (BASE 0x0380))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0240
#             IO base alignment 32 bytes
#             Number of IO addresses required: 16
# (IO 2 (BASE 0x0220))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0e0d
#             Maximum IO base address 0x0e0d
#             IO base alignment 1 bytes
#             Number of IO addresses required: 3
# (IO 3 (BASE 0x0e0d))
#       IRQ 5, 7 or 10.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
#       First DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed type F
# (DMA 0 (CHANNEL 0))

#       Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0534
#             Maximum IO base address 0x0ff0
#             IO base alignment 4 bytes
#             Number of IO addresses required: 4
# (IO 0 (BASE 0x0534))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0380
#             Maximum IO base address 0x03f0
#             IO base alignment 16 bytes
#             Number of IO addresses required: 12
# (IO 1 (BASE 0x0380))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0240
#             IO base alignment 32 bytes
#             Number of IO addresses required: 16
# (IO 2 (BASE 0x0220))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0e8d
#             Maximum IO base address 0x0e8d
#             IO base alignment 1 bytes
#             Number of IO addresses required: 3
# (IO 3 (BASE 0x0e8d))
#       IRQ 5, 7 or 10.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
#       First DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed type F
# (DMA 0 (CHANNEL 0))

#     End dependent functions
# (ACT Y)
))
#
# Logical device id PNPb02f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be
changed if required
# Don't forget to uncomment the activate (ACT Y) when happy

(CONFIGURE OPT0931/-1 (LD 2
#     ANSI string -->Game Port<--
#     Logical device decodes 16 bit IO address lines
#         Minimum IO base address 0x0200
#         Maximum IO base address 0x0207
#         IO base alignment 1 bytes
#         Number of IO addresses required: 1
# (IO 0 (BASE 0x0200))
# (ACT Y)
))
#
# Logical device id OPT0002
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be
changed if required
# Don't forget to uncomment the activate (ACT Y) when happy

(CONFIGURE OPT0931/-1 (LD 3
#     ANSI string -->MPU401<--
#     Logical device decodes 16 bit IO address lines
#         Minimum IO base address 0x0330
#         Maximum IO base address 0x0360
#         IO base alignment 16 bytes
#         Number of IO addresses required: 2
# (IO 0 (BASE 0x0330))
(ACT Y)))
# End tag... Checksum 0x00 (OK)