Can burn data but cannot burn audio???

Can burn data but cannot burn audio???

Post by Martin prime » Tue, 13 Aug 2002 04:42:47



Ok guys here's my problem:

i got no problem burning data cd's but when i try to burn audio it
fails here's the system config and the error itself

mandrake 8.2
cdr-rw LG CED-8080B
cdrecord


-audio /home/coolman/Music/*.wav
Cdrecord 1.11a28 (i586-mandrake-linux-gnu) Copyright (C) 1995-2002
J?rg Schilling
TOC Type: 0 = CD-DA
scsidev: '0,0,0'
scsibus: 0 target: 0 lun: 0
Linux sg driver version: 3.1.22
Using libscg version 'schily-0.6'
atapi: 1
Device type    : Removable CD-ROM
Version        : 0
Response Format: 1
Vendor_info    : 'LG      '
Identifikation : 'CD-RW CED-8080B '
Revision       : '1.06'
Device seems to be: Generic mmc CD-RW.
Using generic SCSI-3/mmc CD-R driver (mmc_cdr).
Driver flags   : SWABAUDIO
Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P
RAW/R96R
Drive buf size : 25165920 = 24576 KB
FIFO size      : 4194304 = 4096 KB
Track 01: audio   40 MB (03:59.04) no preemp pad    
Track 02: audio   38 MB (03:48.64) no preemp pad    
Track 03: audio   37 MB (03:41.07) no preemp pad    
Track 04: audio   17 MB (01:45.48) no preemp pad    
Track 05: audio   40 MB (03:59.72) no preemp pad    
Track 06: audio   38 MB (03:48.88) no preemp pad    
Track 07: audio   37 MB (03:42.98) no preemp pad    
Track 08: audio   40 MB (04:00.84) no preemp pad    
Track 09: audio   33 MB (03:16.17) no preemp pad    
Track 10: audio   40 MB (04:02.65) no preemp pad    
Track 11: audio   38 MB (03:47.36) no preemp pad    
Track 12: audio   41 MB (04:04.58) no preemp pad    
Track 13: audio   44 MB (04:21.56) no preemp pad    
Track 14: audio   44 MB (04:27.12) no preemp pad    
Track 15: audio   56 MB (05:33.21) no preemp pad    
Track 16: audio   53 MB (05:18.95) no preemp pad    
Track 17: audio   39 MB (03:53.24) no preemp pad    
Total size:      686 MB (68:03.69) = 306277 sectors
Lout start:      687 MB (68:05/52) = 306277 sectors
Current Secsize: 2048
ATIP info from disk:
  Indicated writing power: 5
  Is not unrestricted
  Is not erasable
  Disk sub type: Medium Type A, low Beta category (A-) (2)
  ATIP start of lead in:  -11634 (97:26/66)
  ATIP start of lead out: 359849 (79:59/74)
Disk type:    Short strategy type (Phthalocyanine or similar)
Manuf. index: 3
Manufacturer: CMC Magnetics Corporation
Blocks total: 359849 Blocks current: 359849 Blocks remaining: 53572
Starting to write CD/DVD at speed 2 in real TAO mode for single
session.
Last chance to quit, starting real write in 0 seconds. Operation
starts.
Waiting for reader process to fill input buffer ... input buffer
ready.
Performing OPC...
Starting new track at sector: 0
Track 01:   0 of  40 MB written.cdrecord: Input/output error.
write_g1: scsi sendcmd: no error
CDB:  2A 00 00 00 00 00 00 00 1B 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 05 00 00 00 00 0A 00 00 00 00 64 00 00 00
Sense Key: 0x5 Illegal Request, Segment 0
Sense Code: 0x64 Qual 0x00 (illegal mode for this track) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 0.003s timeout 40s

write track data: error after 0 bytes
Sense Bytes: 70 00 00 00 00 00 00 0A 00 00 00 00 00 00 00 00 00 00
Writing  time:    5.020s
Fixating...
cdrecord: Input/output error. close track/session: scsi sendcmd: no
error
CDB:  5B 00 02 00 00 00 00 00 00 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 05 00 00 00 00 0A 00 00 00 00 2C 04 00 00
Sense Key: 0x5 Illegal Request, Segment 0
Sense Code: 0x2C Qual 0x04 (current program area is empty) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 0.000s timeout 480s
cmd finished after 0.000s timeout 480s
Fixating time:    0.002s
cdrecord: fifo had 64 puts and 1 gets.
cdrecord: fifo was 0 times empty and 0 times full, min fill was 100%.

Now thats very odd cuz there is no problem burning data cd's ...

anyone that could help me fixing that it will be greatly appreciated.

thnx


Martin Primeau

 
 
 

Can burn data but cannot burn audio???

Post by andre » Tue, 13 Aug 2002 01:10:54


what about
cdrecord -v speed=4 dev=0,0,0 -audio -pad
cdrecord -v speed=4 dev=0,0,0 -audio -preemp

 
 
 

Can burn data but cannot burn audio???

Post by Martin prime » Tue, 13 Aug 2002 12:46:28



> what about
> cdrecord -v speed=4 dev=0,0,0 -audio -pad
> cdrecord -v speed=4 dev=0,0,0 -audio -preemp


/home/coolman/music/*.wav
Cdrecord 1.11a28 (i586-mandrake-linux-gnu) Copyright (C) 1995-2002
J?rg Schilling
TOC Type: 0 = CD-DA
scsidev: '0,0,0'
scsibus: 0 target: 0 lun: 0
Linux sg driver version: 3.1.22
Using libscg version 'schily-0.6'
atapi: 1
Device type    : Removable CD-ROM
Version        : 0
Response Format: 1
Vendor_info    : 'LG      '
Identifikation : 'CD-RW CED-8080B '
Revision       : '1.06'
Device seems to be: Generic mmc CD-RW.
Using generic SCSI-3/mmc CD-R driver (mmc_cdr).
Driver flags   : SWABAUDIO
Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P
RAW/R96R
Drive buf size : 25165920 = 24576 KB
FIFO size      : 4194304 = 4096 KB
Track 01: audio   33 MB (03:16.17) no preemp pad    
Track 02: audio   40 MB (04:02.65) no preemp pad    
Track 03: audio   38 MB (03:47.36) no preemp pad    
Total size:      112 MB (11:10.21) = 50266 sectors
Lout start:      113 MB (11:12/16) = 50266 sectors
Current Secsize: 2048
ATIP info from disk:
  Indicated writing power: 5
  Is not unrestricted
  Is not erasable
  Disk sub type: Medium Type A, low Beta category (A-) (2)
  ATIP start of lead in:  -11634 (97:26/66)
  ATIP start of lead out: 359849 (79:59/74)
Disk type:    Short strategy type (Phthalocyanine or similar)
Manuf. index: 3
Manufacturer: CMC Magnetics Corporation
Blocks total: 359849 Blocks current: 359849 Blocks remaining: 309583
Starting to write CD/DVD at speed 4 in real TAO mode for single
session.
Last chance to quit, starting real write in 0 seconds. Operation
starts.
Waiting for reader process to fill input buffer ... input buffer
ready.
Performing OPC...
Starting new track at sector: 0
Track 01:   0 of  33 MB written.cdrecord: Input/output error.
write_g1: scsi sendcmd: no error
CDB:  2A 00 00 00 00 00 00 00 1B 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 05 00 00 00 00 0A 00 00 00 00 64 00 00 00
Sense Key: 0x5 Illegal Request, Segment 0
Sense Code: 0x64 Qual 0x00 (illegal mode for this track) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 0.002s timeout 40s

write track data: error after 0 bytes
Sense Bytes: 70 00 00 00 00 00 00 0A 00 00 00 00 00 00 00 00 00 00
Writing  time:    5.020s
Fixating...
cdrecord: Input/output error. close track/session: scsi sendcmd: no
error
CDB:  5B 00 02 00 00 00 00 00 00 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 05 00 00 00 00 0A 00 00 00 00 2C 04 00 00
Sense Key: 0x5 Illegal Request, Segment 0
Sense Code: 0x2C Qual 0x04 (current program area is empty) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 0.000s timeout 480s
cmd finished after 0.000s timeout 480s
Fixating time:    0.002s
cdrecord: fifo had 64 puts and 1 gets.
cdrecord: fifo was 0 times empty and 0 times full, min fill was 100%.

and


/home/coolman/music/*.wav
Cdrecord 1.11a28 (i586-mandrake-linux-gnu) Copyright (C) 1995-2002
J?rg Schilling
TOC Type: 0 = CD-DA
scsidev: '0,0,0'
scsibus: 0 target: 0 lun: 0
Linux sg driver version: 3.1.22
Using libscg version 'schily-0.6'
atapi: 1
Device type    : Removable CD-ROM
Version        : 0
Response Format: 1
Vendor_info    : 'LG      '
Identifikation : 'CD-RW CED-8080B '
Revision       : '1.06'
Device seems to be: Generic mmc CD-RW.
Using generic SCSI-3/mmc CD-R driver (mmc_cdr).
Driver flags   : SWABAUDIO
Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P
RAW/R96R
Drive buf size : 1024000 = 1000 KB
FIFO size      : 4194304 = 4096 KB
cdrecord: Bad audio track size 34606080 for track 01.
cdrecord: Audio tracks must be at least 705600 bytes and a multiple of
2352.
cdrecord: See -pad option.

read about those lg drives that they are a pain in the ass when trying
to burn audio files...

should i give up or someone got it working?

thnx

 
 
 

Can burn data but cannot burn audio???

Post by B'ichel » Wed, 14 Aug 2002 04:01:06



> should i give up or someone got it working?

> thnx

        How is cdrdao working for you? I never used cdrecord to do
TAO audio. I go straight to cdrdao as I like to record songs without
predefined gaps. (just a referesher, look at the cd-writing HOWTO in
reguards to using cdrdao and cdrecord.

--

                        The New Cnews maintainer
                                B'ichela

 
 
 

1. Burning data/audio CD Error Audio

Hi,

my Hardware:

Buslogic BT948
2xIBM DORS 32160 U
P-166, 64 MB RAM
Phillips CDD2000/00

Kernel 2.0.21  Cdwrite-2.0  xcdroast-0.95 and all the needed goodies

ok - I burned a CD data/audio  - everything seemed to perform well and I
pushed the needed cancel buttons when finished writing - no other way to
get back to the main menu in xcdroast, isdn't it ?

Anyway after I wrote the CD, I looked at the data and everything was
there.
I put it in my home CD player and heard the audio from the Game.
I put it in the computer to play and whe nthe audio tracks come it
crashes.
Also no software CD-PLayer is able to play the  audio's.

What could have happened here ? I put audioread on 4x speed (the writer
reads 4x and writes 2x)
I choose "all" when choosing the tracks to copy. I had enough HS space.
I choose "big indian" because I use a Phillips.

I don't want to burn on W95 - oh no please !

Any hints and experiences - please reply - I'm waiting desperatly

bye
--

   Christophe

--------------------------------------------------------------------------

Hamburg, Germany                      
--------------------------------------------------------------------------

In newsgroups please reply also by email - thanks

2. Is there a used computer hardware newsgroup?

3. Should MP3 be burnded as audio or data and how to verify audio burning?

4. No X cursor???

5. Burning successful with growisofs but cannot read burnt DVDs

6. Xfree 1.2 leaves screen in graph-mode after exit, runx !work

7. newbie (sort of) can't burn data to cdr, audio works fine.

8. Network problems...please help!

9. calculate MD5SUM on a burned disk to check distro burn?

10. Please help -- error in burning or reading burned CD

11. Burn baby burn!...?

12. CD burning issues under redhat with all burning applications

13. How burn wav files to cd audio ?