How to install an internal TPlink 336 modem (Davicom)?

How to install an internal TPlink 336 modem (Davicom)?

Post by ·é?? » Wed, 01 Dec 1999 04:00:00



Hi,
    I am a novice of Linux and I am not an English native. Could here anyone
tell me how to install TPlink336 modem(Davicom) on RedHat Linux 5.1? I
installed Linux on my machine with WIN98.

    In the control panel of Windoze, my modem is using the following
resource,

port 0x3E8-0x3EF
irq 5

tell me how to config the isapnp.conf so that it can work properly with
isapnp. and after that,what should i do?
please do not tell me how to upgrade to Redhat 6.1 . Thank you.



# $Id: pnpdump.c,v 1.10 1997/07/14 22:30:47 fox Exp $
# This is free software, see the sources for details.
# This software has NO WARRANTY, use at your OWN RISK
#
# For details of this file format, see isapnp.conf(5)
#
# For latest information on isapnp and pnpdump see:
# http://www.roestock.demon.co.uk/isapnptools/
#
# Compiler flags: -DREALTIME -DNEEDSETSCHEDULER
#
# Trying port address 0203
# Board 1 has serial identifier c5 00 00 11 11 01 00 36 10

# (DEBUG)
(READPORT 0x0203)
(ISOLATE)
(IDENTIFY *)

# Card 1: (serial identifier c5 00 00 11 11 01 00 36 10)
# DAV0001 Serial No 4369 [checksum c5]
# Version 1.0, Vendor version 1.0
# ANSI string -->DAVICOM 336PNP MODEM<--
#
# Logical device id DAV0336
#     Device support I/O range check register
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed
if required
# Don't forget to uncomment the activate (ACT Y) when happy

(CONFIGURE DAV0001/4369 (LD 0

# Multiple choice time, choose one only !

#     Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x02f8
#             Maximum IO base address 0x02f8
#             IO base alignment 8 bytes
#             Number of IO addresses required: 8
# (IO 0 (BASE 0x02f8))
#       IRQ 3.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 3 (MODE +E)))

#       Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x03f8
#             Maximum IO base address 0x03f8
#             IO base alignment 8 bytes
#             Number of IO addresses required: 8
# (IO 0 (BASE 0x03f8))
#       IRQ 4.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 4 (MODE +E)))

#       Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x03e8
#             Maximum IO base address 0x03e8
#             IO base alignment 8 bytes
#             Number of IO addresses required: 8
# (IO 0 (BASE 0x03e8))
#       IRQ 4.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 4 (MODE +E)))

#       Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x02e8
#             Maximum IO base address 0x02e8
#             IO base alignment 8 bytes
#             Number of IO addresses required: 8
# (IO 0 (BASE 0x02e8))
#       IRQ 3.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 3 (MODE +E)))

#       Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x03e8
#             Maximum IO base address 0x03e8
#             IO base alignment 8 bytes
#             Number of IO addresses required: 8
# (IO 0 (BASE 0x03e8))
#       IRQ 5.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))

#       Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x02e8
#             Maximum IO base address 0x02e8
#             IO base alignment 8 bytes
#             Number of IO addresses required: 8
# (IO 0 (BASE 0x02e8))
#       IRQ 5.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))

#       Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x03e8
#             Maximum IO base address 0x03e8
#             IO base alignment 8 bytes
#             Number of IO addresses required: 8
# (IO 0 (BASE 0x03e8))
#       IRQ 3, 4, 5, 7, 10, 11, 12 or 15.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 3 (MODE +E)))

#       Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x02e8
#             Maximum IO base address 0x02e8
#             IO base alignment 8 bytes
#             Number of IO addresses required: 8
# (IO 0 (BASE 0x02e8))
#       IRQ 3, 4, 5, 7, 10, 11, 12 or 15.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 3 (MODE +E)))

#       Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x03f8
#             Maximum IO base address 0x03f8
#             IO base alignment 8 bytes
#             Number of IO addresses required: 8
# (IO 0 (BASE 0x03f8))
#       IRQ 3, 4, 5, 7, 10, 11, 12 or 15.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 3 (MODE +E)))

#       Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x02f8
#             Maximum IO base address 0x02f8
#             IO base alignment 8 bytes
#             Number of IO addresses required: 8
# (IO 0 (BASE 0x02f8))
#       IRQ 3, 4, 5, 7, 10, 11, 12 or 15.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 3 (MODE +E)))

#       Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0200
#             Maximum IO base address 0x03f8
#             IO base alignment 8 bytes
#             Number of IO addresses required: 8
# (IO 0 (BASE 0x0200))
#       IRQ 3, 4, 5, 7, 10, 11, 12 or 15.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 3 (MODE +E)))

#     End dependent functions
# (ACT Y)
))
# End tag... Checksum 0x00 (OK)

# Returns all cards to the "Wait for Key" state
(WAITFORKEY)


--
------
When you shot at a king,you must kill him.

ICQ #32028243#

 
 
 

1. Help: Modem doesn't work -- Compaq Presario 336-VSC Modem

I'm using a Compaq Presario 336-VSC Modem which works very well under
Win95. But it seemed that linux can't recognize it at all. When I run
kermit, I got an error message as follows,

C-Kermit> set line /dev/cua1
C-Kermit> /dev/cua1 is not a terminal device
C-Kermit> sorry, can't open connection to /dev/cua1

When I am trying setserial -a /dev/ttyS1, the irq(3) and port(0x02f8)
are ok but uart is UNKNOWN.

It's a fax-modem connected to COM2 and thus the device name should be
/dev/cua1 and /dev/ttyS1.

Could you please give me any idea about what is going wrong? Do I need
a special device driver?

Lizhan Yao

2. Mitsumi Double Speed Drive

3. Drivers for Compaq Presario 336-VSC Modem (ATT Controlerless Modem)

4. Mailshot software

5. Hayes 336 fax/modem PCMCIA problem w/RH 6.1 -- can't activate modem

6. Can ping outside but no telnet or ftp!

7. Compaq Presario 336-DF 56k Upgradeable Modem & Linux

8. kcron or gcron?

9. Newbie with a Hayes Optima 336 external modem

10. Hayes 336 PCMCIA Modem problems

11. Have anybody setup a Compaq Presario 336-VCS modem?

12. Compaq 336-VSC Modem

13. Hayes 336 Int Speakerphone Modem