Board index Linux Hardware

D-Link DFE-530TX NIC trouble

D-Link DFE-530TX NIC trouble

Post by Keith Beacha » Sun, 12 Nov 2000 04:00:00



I am having trouble configuring a D-Link DFE-530TX ethernet card.  I get
errors
like "init_module: Device or resource busy" when I try to load the driver.
"via-diag" finds the adapter at the expected address and the adapter appears
to work all right in Windows.

I have also checked that the "PnP OS" setting in the BIOS is turned off,
which
was a suggestion I saw in a previous post.  I have included the output
from modprobe, via-diag, lspci, and dmesg below in case they are useful
in solving this problem.

Does anyone have a suggestion as to how to fix this?

Thanks,

Brent

*** output from "modprobe via-rhine" ***

/lib/modules/2.2.16/net/via-rhine.o: init_module: Device or resource busy
/lib/modules/2.2.16/net/via-rhine.o: insmod
/lib/modules/2.2.16/net/via-rhine.o failed
/lib/modules/2.2.16/net/via-rhine.o: insmod via-rhine failed

*** output from "via-diag -aa -ee" ***


 http://www.scyld.com/diag/index.html
Index #1: Found a VIA VT3065 Rhine-II adapter at 0xd400.
 Station address 00:00:00:00:00:00.
 Tx disabled, Rx disabled, half-duplex (0x0804).
  Receive  mode is 0x00: Unknown/invalid.
  Transmit mode is 0x00: Normal transmit, 128 byte threshold.
VIA VT3065 Rhine-II chip registers at 0xd400
 0x000: 00000000 00000000 00000804 00000000 00000000 00000000 00000000
00000000
 0x020: 00000400 00000000 00000000 00000000 00000000 00000000 00000000
00000000
 0x040: 00000000 00000000 00000000 00000000 00000000 00000000 00000000
fffff5ff
 0x060: 00000000 00000000 00000000 0e091308 00008100 08000080 02470000
00000000
 No interrupt sources are pending (0000).
  Access to the EEPROM has been disabled (0x80).
    Direct reading or writing is not possible.
EEPROM contents (Assumed from chip registers):
0x100:  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x110:  00 00 00 00 00 00 00 00 09 0e 00 00 47 02 73 73

*** output from "lspci" ***

00:00.0 Host bridge: Intel Corporation 430TX - 82439TX MTXC (rev 01)
00:01.0 ISA bridge: Intel Corporation 82371AB PIIX4 ISA (rev 01)
00:01.1 IDE interface: Intel Corporation 82371AB PIIX4 IDE (rev 01)
00:01.2 USB Controller: Intel Corporation 82371AB PIIX4 USB (rev 01)
00:01.3 Bridge: Intel Corporation 82371AB PIIX4 ACPI (rev 01)
00:09.0 Ethernet controller: VIA Technologies, Inc.: Unknown device 3065
(rev 43)
00:0a.0 VGA compatible controller: ATI Technologies Inc 3D Rage Pro 215GP
(rev 5c)

*** output from  "dmesg" ***


(release)) #1 Sun Jul 9 18:54:13 GMT 2000
Detected 233867 kHz processor.
ide_setup: hdb=ide-scsi
ide_setup: idebus=66
Console: colour VGA+ 80x25
Calibrating delay loop... 466.94 BogoMIPS
Memory: 29828k/32768k available (1500k kernel code, 416k reserved, 652k
data, 76k init, 0k bigmem)
Dentry hash table entries: 4096 (order 3, 32k)
Buffer cache hash table entries: 32768 (order 5, 128k)
Page cache hash table entries: 8192 (order 3, 32k)
VFS: Diskquotas version dquot_6.4.0 initialized
CPU: Intel Pentium MMX stepping 03
Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
Checking 'hlt' instruction... OK.
Intel Pentium with F0 0F bug - workaround enabled.
POSIX conformance testing by UNIFIX
PCI: PCI BIOS revision 2.10 entry at 0xf0560, last bus=0
PCI: Using configuration type 1
PCI: Probing PCI hardware
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0 for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
TCP: Hash tables configured (ehash 32768 bhash 32768)
Initializing RT netlink socket
Starting kswapd v 1.5
Detected PS/2 Mouse Port.
pty: 256 Unix98 ptys configured
Real Time Clock Driver v1.09
RAM disk driver initialized:  16 RAM disks of 64000K size
loop: registered device at major 7
Uniform Multi-Platform E-IDE driver Revision: 6.30
ide: Assuming 66MHz system bus speed for PIO modes
PIIX4: IDE controller on PCI bus 00 dev 09
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:pio, hdb:pio
    ide1: BM-DMA at 0xe008-0xe00f, BIOS settings: hdc:pio, hdd:pio
hda: WDC AC34300L, ATA DISK drive
hdb: Hewlett-Packard CD-Writer Plus 9100, ATAPI CDROM drive
hdc: Maxtor 53073U6, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: WDC AC34300L, 4104MB w/256kB Cache, CHS=8896/15/63, UDMA(33)
hdc: Maxtor 53073U6, 29311MB w/2048kB Cache, CHS=59554/16/63, UDMA(33)
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
LVM version 0.8e  by Heinz Mauelshagen  (4/1/2000)
lvm -- Driver successfully initialized
md driver 0.36.6 MAX_MD_DEV=4, MAX_REAL=8
linear personality registered
raid0 personality registered
raid1 personality registered
raid5 personality registered
scsi : 0 hosts.
scsi : detected total.
Partition check:
 hda: [EZD] [remap 0->1] [523/255/63] hda1
 hdc: [PTBL] [1027/255/63] hdc1 hdc2 < hdc5 hdc6 hdc7 hdc8 >
RAMDISK: Compressed image found at block 0
Uncompressing........................done.
VFS: Mounted root (ext2 filesystem).
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
scsi : 1 host.
  Vendor: HP        Model: CD-Writer+ 9100   Rev: 1.0c
  Type:   CD-ROM                             ANSI SCSI revision: 02
Detected scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
sr0: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.11
VFS: Mounted root (ext2 filesystem) readonly.
change_root: old root has d_count=1
Trying to unmount old root ... okay
Freeing unused kernel memory: 76k freed
Adding Swap: 136512k swap-space (priority -1)
Serial driver version 4.27 with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
via-rhine.c:v1.01 2/27/99  Written by Donald Becker
  http://cesdis.gsfc.nasa.gov/linux/drivers/via-rhine.html
via-rhine.c:v1.01 2/27/99  Written by Donald Becker
  http://cesdis.gsfc.nasa.gov/linux/drivers/via-rhine.html
via-rhine.c:v1.01 2/27/99  Written by Donald Becker
  http://cesdis.gsfc.nasa.gov/linux/drivers/via-rhine.html
via-rhine.c:v1.01 2/27/99  Written by Donald Becker
  http://cesdis.gsfc.nasa.gov/linux/drivers/via-rhine.html
via-rhine.c:v1.01 2/27/99  Written by Donald Becker
  http://cesdis.gsfc.nasa.gov/linux/drivers/via-rhine.html
PnP: Calling quirk for 01:00
PnP: Calling quirk for 01:02
isapnp: Card 'Creative SB AWE64 PnP'
isapnp: Card 'U.S. Robotics Inc. x2 Winmodem Voice   '
isapnp: 2 Plug & Play cards detected total
via-rhine.c:v1.01 2/27/99  Written by Donald Becker
  http://cesdis.gsfc.nasa.gov/linux/drivers/via-rhine.html
via-rhine.c:v1.01 2/27/99  Written by Donald Becker
  http://cesdis.gsfc.nasa.gov/linux/drivers/via-rhine.html
via-rhine.c:v1.01 2/27/99  Written by Donald Becker
  http://cesdis.gsfc.nasa.gov/linux/drivers/via-rhine.html
via-rhine.c:v1.01 2/27/99  Written by Donald Becker
  http://cesdis.gsfc.nasa.gov/linux/drivers/via-rhine.html

 
 
 
Top

D-Link DFE-530TX NIC trouble

Post by Kevin Lon » Sun, 12 Nov 2000 04:00:00


I had the same NIC in my Mandrake 7.1 setup.  A number of drivers including
the Rhine ones worked, but communication was never better than pinging.
In the end I switched to an Intel Etherexpress Pro and never looked back.

Kevin

> I am having trouble configuring a D-Link DFE-530TX ethernet card.  I get
> errors
> like "init_module: Device or resource busy" when I try to load the driver.
> "via-diag" finds the adapter at the expected address and the adapter
appears
> to work all right in Windows.

> I have also checked that the "PnP OS" setting in the BIOS is turned off,
> which
> was a suggestion I saw in a previous post.  I have included the output
> from modprobe, via-diag, lspci, and dmesg below in case they are useful
> in solving this problem.

> Does anyone have a suggestion as to how to fix this?

> Thanks,

> Brent

> *** output from "modprobe via-rhine" ***

> /lib/modules/2.2.16/net/via-rhine.o: init_module: Device or resource busy
> /lib/modules/2.2.16/net/via-rhine.o: insmod
> /lib/modules/2.2.16/net/via-rhine.o failed
> /lib/modules/2.2.16/net/via-rhine.o: insmod via-rhine failed

> *** output from "via-diag -aa -ee" ***


>  http://www.scyld.com/diag/index.html
> Index #1: Found a VIA VT3065 Rhine-II adapter at 0xd400.
>  Station address 00:00:00:00:00:00.
>  Tx disabled, Rx disabled, half-duplex (0x0804).
>   Receive  mode is 0x00: Unknown/invalid.
>   Transmit mode is 0x00: Normal transmit, 128 byte threshold.
> VIA VT3065 Rhine-II chip registers at 0xd400
>  0x000: 00000000 00000000 00000804 00000000 00000000 00000000 00000000
> 00000000
>  0x020: 00000400 00000000 00000000 00000000 00000000 00000000 00000000
> 00000000
>  0x040: 00000000 00000000 00000000 00000000 00000000 00000000 00000000
> fffff5ff
>  0x060: 00000000 00000000 00000000 0e091308 00008100 08000080 02470000
> 00000000
>  No interrupt sources are pending (0000).
>   Access to the EEPROM has been disabled (0x80).
>     Direct reading or writing is not possible.
> EEPROM contents (Assumed from chip registers):
> 0x100:  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 0x110:  00 00 00 00 00 00 00 00 09 0e 00 00 47 02 73 73

> *** output from "lspci" ***

> 00:00.0 Host bridge: Intel Corporation 430TX - 82439TX MTXC (rev 01)
> 00:01.0 ISA bridge: Intel Corporation 82371AB PIIX4 ISA (rev 01)
> 00:01.1 IDE interface: Intel Corporation 82371AB PIIX4 IDE (rev 01)
> 00:01.2 USB Controller: Intel Corporation 82371AB PIIX4 USB (rev 01)
> 00:01.3 Bridge: Intel Corporation 82371AB PIIX4 ACPI (rev 01)
> 00:09.0 Ethernet controller: VIA Technologies, Inc.: Unknown device 3065
> (rev 43)
> 00:0a.0 VGA compatible controller: ATI Technologies Inc 3D Rage Pro 215GP
> (rev 5c)

> *** output from  "dmesg" ***


> (release)) #1 Sun Jul 9 18:54:13 GMT 2000
> Detected 233867 kHz processor.
> ide_setup: hdb=ide-scsi
> ide_setup: idebus=66
> Console: colour VGA+ 80x25
> Calibrating delay loop... 466.94 BogoMIPS
> Memory: 29828k/32768k available (1500k kernel code, 416k reserved, 652k
> data, 76k init, 0k bigmem)
> Dentry hash table entries: 4096 (order 3, 32k)
> Buffer cache hash table entries: 32768 (order 5, 128k)
> Page cache hash table entries: 8192 (order 3, 32k)
> VFS: Diskquotas version dquot_6.4.0 initialized
> CPU: Intel Pentium MMX stepping 03
> Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
> Checking 'hlt' instruction... OK.
> Intel Pentium with F0 0F bug - workaround enabled.
> POSIX conformance testing by UNIFIX
> PCI: PCI BIOS revision 2.10 entry at 0xf0560, last bus=0
> PCI: Using configuration type 1
> PCI: Probing PCI hardware
> Linux NET4.0 for Linux 2.2
> Based upon Swansea University Computer Society NET3.039
> NET4: Unix domain sockets 1.0 for Linux NET4.0.
> NET4: Linux TCP/IP 1.0 for NET4.0
> IP Protocols: ICMP, UDP, TCP, IGMP
> TCP: Hash tables configured (ehash 32768 bhash 32768)
> Initializing RT netlink socket
> Starting kswapd v 1.5
> Detected PS/2 Mouse Port.
> pty: 256 Unix98 ptys configured
> Real Time Clock Driver v1.09
> RAM disk driver initialized:  16 RAM disks of 64000K size
> loop: registered device at major 7
> Uniform Multi-Platform E-IDE driver Revision: 6.30
> ide: Assuming 66MHz system bus speed for PIO modes
> PIIX4: IDE controller on PCI bus 00 dev 09
> PIIX4: chipset revision 1
> PIIX4: not 100% native mode: will probe irqs later
>     ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:pio, hdb:pio
>     ide1: BM-DMA at 0xe008-0xe00f, BIOS settings: hdc:pio, hdd:pio
> hda: WDC AC34300L, ATA DISK drive
> hdb: Hewlett-Packard CD-Writer Plus 9100, ATAPI CDROM drive
> hdc: Maxtor 53073U6, ATA DISK drive
> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> ide1 at 0x170-0x177,0x376 on irq 15
> hda: WDC AC34300L, 4104MB w/256kB Cache, CHS=8896/15/63, UDMA(33)
> hdc: Maxtor 53073U6, 29311MB w/2048kB Cache, CHS=59554/16/63, UDMA(33)
> Floppy drive(s): fd0 is 1.44M
> FDC 0 is a post-1991 82077
> LVM version 0.8e  by Heinz Mauelshagen  (4/1/2000)
> lvm -- Driver successfully initialized
> md driver 0.36.6 MAX_MD_DEV=4, MAX_REAL=8
> linear personality registered
> raid0 personality registered
> raid1 personality registered
> raid5 personality registered
> scsi : 0 hosts.
> scsi : detected total.
> Partition check:
>  hda: [EZD] [remap 0->1] [523/255/63] hda1
>  hdc: [PTBL] [1027/255/63] hdc1 hdc2 < hdc5 hdc6 hdc7 hdc8 >
> RAMDISK: Compressed image found at block 0
> Uncompressing........................done.
> VFS: Mounted root (ext2 filesystem).
> scsi0 : SCSI host adapter emulation for IDE ATAPI devices
> scsi : 1 host.
>   Vendor: HP        Model: CD-Writer+ 9100   Rev: 1.0c
>   Type:   CD-ROM                             ANSI SCSI revision: 02
> Detected scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
> sr0: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray
> Uniform CD-ROM driver Revision: 3.11
> VFS: Mounted root (ext2 filesystem) readonly.
> change_root: old root has d_count=1
> Trying to unmount old root ... okay
> Freeing unused kernel memory: 76k freed
> Adding Swap: 136512k swap-space (priority -1)
> Serial driver version 4.27 with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ
enabled
> ttyS00 at 0x03f8 (irq = 4) is a 16550A
> ttyS01 at 0x02f8 (irq = 3) is a 16550A
> via-rhine.c:v1.01 2/27/99  Written by Donald Becker
>   http://cesdis.gsfc.nasa.gov/linux/drivers/via-rhine.html
> via-rhine.c:v1.01 2/27/99  Written by Donald Becker
>   http://cesdis.gsfc.nasa.gov/linux/drivers/via-rhine.html
> via-rhine.c:v1.01 2/27/99  Written by Donald Becker
>   http://cesdis.gsfc.nasa.gov/linux/drivers/via-rhine.html
> via-rhine.c:v1.01 2/27/99  Written by Donald Becker
>   http://cesdis.gsfc.nasa.gov/linux/drivers/via-rhine.html
> via-rhine.c:v1.01 2/27/99  Written by Donald Becker
>   http://cesdis.gsfc.nasa.gov/linux/drivers/via-rhine.html
> PnP: Calling quirk for 01:00
> PnP: Calling quirk for 01:02
> isapnp: Card 'Creative SB AWE64 PnP'
> isapnp: Card 'U.S. Robotics Inc. x2 Winmodem Voice   '
> isapnp: 2 Plug & Play cards detected total
> via-rhine.c:v1.01 2/27/99  Written by Donald Becker
>   http://cesdis.gsfc.nasa.gov/linux/drivers/via-rhine.html
> via-rhine.c:v1.01 2/27/99  Written by Donald Becker
>   http://cesdis.gsfc.nasa.gov/linux/drivers/via-rhine.html
> via-rhine.c:v1.01 2/27/99  Written by Donald Becker
>   http://cesdis.gsfc.nasa.gov/linux/drivers/via-rhine.html
> via-rhine.c:v1.01 2/27/99  Written by Donald Becker
>   http://cesdis.gsfc.nasa.gov/linux/drivers/via-rhine.html


 
 
 
Top

D-Link DFE-530TX NIC trouble

Post by Séphane Gauber » Sun, 12 Nov 2000 04:00:00


Go and get the latest via-rhine driver from
http://www.scyld.com/network/ethercard.html
v1.01 of the driver doesn't support the VIA VT3065 Rhine-II.

Given the output from your via-diag command, you may encounter the same
problem I encounterd once you'll have compiled the latest via-rhine driver.

If your NIC hardware address doesn't appears correctly in the output of
ifconfig (if you get 00:00:00:00:00:00 like with via-diag), try these two
commands before loading the via-rhine module :

pci-config -S -# <the pci number of you NIC>
pci-config -W -# <the pci number of you NIC>

It works for me. I don't know why, but it works.

Stephane

 
 
 
Top

D-Link DFE-530TX NIC trouble

Post by Joe Umike » Mon, 13 Nov 2000 10:26:56



> I am having trouble configuring a D-Link DFE-530TX ethernet card.  I get
> errors
> like "init_module: Device or resource busy" when I try to load the driver.
> "via-diag" finds the adapter at the expected address and the adapter appears
> to work all right in Windows.

> I have also checked that the "PnP OS" setting in the BIOS is turned off,
> which
> was a suggestion I saw in a previous post.  I have included the output
> from modprobe, via-diag, lspci, and dmesg below in case they are useful
> in solving this problem.

> Does anyone have a suggestion as to how to fix this?

> Thanks,

> Brent

> *** output from "modprobe via-rhine" ***

> /lib/modules/2.2.16/net/via-rhine.o: init_module: Device or resource busy
> /lib/modules/2.2.16/net/via-rhine.o: insmod
> /lib/modules/2.2.16/net/via-rhine.o failed
> /lib/modules/2.2.16/net/via-rhine.o: insmod via-rhine failed

> *** output from "via-diag -aa -ee" ***


>  http://www.scyld.com/diag/index.html
> Index #1: Found a VIA VT3065 Rhine-II adapter at 0xd400.
>  Station address 00:00:00:00:00:00.
>  Tx disabled, Rx disabled, half-duplex (0x0804).
>   Receive  mode is 0x00: Unknown/invalid.
>   Transmit mode is 0x00: Normal transmit, 128 byte threshold.
> VIA VT3065 Rhine-II chip registers at 0xd400
>  0x000: 00000000 00000000 00000804 00000000 00000000 00000000 00000000
> 00000000
>  0x020: 00000400 00000000 00000000 00000000 00000000 00000000 00000000
> 00000000
>  0x040: 00000000 00000000 00000000 00000000 00000000 00000000 00000000
> fffff5ff
>  0x060: 00000000 00000000 00000000 0e091308 00008100 08000080 02470000
> 00000000
>  No interrupt sources are pending (0000).
>   Access to the EEPROM has been disabled (0x80).
>     Direct reading or writing is not possible.
> EEPROM contents (Assumed from chip registers):
> 0x100:  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 0x110:  00 00 00 00 00 00 00 00 09 0e 00 00 47 02 73 73

> *** output from "lspci" ***

> 00:00.0 Host bridge: Intel Corporation 430TX - 82439TX MTXC (rev 01)
> 00:01.0 ISA bridge: Intel Corporation 82371AB PIIX4 ISA (rev 01)
> 00:01.1 IDE interface: Intel Corporation 82371AB PIIX4 IDE (rev 01)
> 00:01.2 USB Controller: Intel Corporation 82371AB PIIX4 USB (rev 01)
> 00:01.3 Bridge: Intel Corporation 82371AB PIIX4 ACPI (rev 01)
> 00:09.0 Ethernet controller: VIA Technologies, Inc.: Unknown device 3065
> (rev 43)
> 00:0a.0 VGA compatible controller: ATI Technologies Inc 3D Rage Pro 215GP
> (rev 5c)

> *** output from  "dmesg" ***


> (release)) #1 Sun Jul 9 18:54:13 GMT 2000
> Detected 233867 kHz processor.
> ide_setup: hdb=ide-scsi
> ide_setup: idebus=66
> Console: colour VGA+ 80x25
> Calibrating delay loop... 466.94 BogoMIPS
> Memory: 29828k/32768k available (1500k kernel code, 416k reserved, 652k
> data, 76k init, 0k bigmem)
> Dentry hash table entries: 4096 (order 3, 32k)
> Buffer cache hash table entries: 32768 (order 5, 128k)
> Page cache hash table entries: 8192 (order 3, 32k)
> VFS: Diskquotas version dquot_6.4.0 initialized
> CPU: Intel Pentium MMX stepping 03
> Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
> Checking 'hlt' instruction... OK.
> Intel Pentium with F0 0F bug - workaround enabled.
> POSIX conformance testing by UNIFIX
> PCI: PCI BIOS revision 2.10 entry at 0xf0560, last bus=0
> PCI: Using configuration type 1
> PCI: Probing PCI hardware
> Linux NET4.0 for Linux 2.2
> Based upon Swansea University Computer Society NET3.039
> NET4: Unix domain sockets 1.0 for Linux NET4.0.
> NET4: Linux TCP/IP 1.0 for NET4.0
> IP Protocols: ICMP, UDP, TCP, IGMP
> TCP: Hash tables configured (ehash 32768 bhash 32768)
> Initializing RT netlink socket
> Starting kswapd v 1.5
> Detected PS/2 Mouse Port.
> pty: 256 Unix98 ptys configured
> Real Time Clock Driver v1.09
> RAM disk driver initialized:  16 RAM disks of 64000K size
> loop: registered device at major 7
> Uniform Multi-Platform E-IDE driver Revision: 6.30
> ide: Assuming 66MHz system bus speed for PIO modes
> PIIX4: IDE controller on PCI bus 00 dev 09
> PIIX4: chipset revision 1
> PIIX4: not 100% native mode: will probe irqs later
>     ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:pio, hdb:pio
>     ide1: BM-DMA at 0xe008-0xe00f, BIOS settings: hdc:pio, hdd:pio
> hda: WDC AC34300L, ATA DISK drive
> hdb: Hewlett-Packard CD-Writer Plus 9100, ATAPI CDROM drive
> hdc: Maxtor 53073U6, ATA DISK drive
> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> ide1 at 0x170-0x177,0x376 on irq 15
> hda: WDC AC34300L, 4104MB w/256kB Cache, CHS=8896/15/63, UDMA(33)
> hdc: Maxtor 53073U6, 29311MB w/2048kB Cache, CHS=59554/16/63, UDMA(33)
> Floppy drive(s): fd0 is 1.44M
> FDC 0 is a post-1991 82077
> LVM version 0.8e  by Heinz Mauelshagen  (4/1/2000)
> lvm -- Driver successfully initialized
> md driver 0.36.6 MAX_MD_DEV=4, MAX_REAL=8
> linear personality registered
> raid0 personality registered
> raid1 personality registered
> raid5 personality registered
> scsi : 0 hosts.
> scsi : detected total.
> Partition check:
>  hda: [EZD] [remap 0->1] [523/255/63] hda1
>  hdc: [PTBL] [1027/255/63] hdc1 hdc2 < hdc5 hdc6 hdc7 hdc8 >
> RAMDISK: Compressed image found at block 0
> Uncompressing........................done.
> VFS: Mounted root (ext2 filesystem).
> scsi0 : SCSI host adapter emulation for IDE ATAPI devices
> scsi : 1 host.
>   Vendor: HP        Model: CD-Writer+ 9100   Rev: 1.0c
>   Type:   CD-ROM                             ANSI SCSI revision: 02
> Detected scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
> sr0: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray
> Uniform CD-ROM driver Revision: 3.11
> VFS: Mounted root (ext2 filesystem) readonly.
> change_root: old root has d_count=1
> Trying to unmount old root ... okay
> Freeing unused kernel memory: 76k freed
> Adding Swap: 136512k swap-space (priority -1)
> Serial driver version 4.27 with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ enabled
> ttyS00 at 0x03f8 (irq = 4) is a 16550A
> ttyS01 at 0x02f8 (irq = 3) is a 16550A
> via-rhine.c:v1.01 2/27/99  Written by Donald Becker
>   http://cesdis.gsfc.nasa.gov/linux/drivers/via-rhine.html
> via-rhine.c:v1.01 2/27/99  Written by Donald Becker
>   http://cesdis.gsfc.nasa.gov/linux/drivers/via-rhine.html
> via-rhine.c:v1.01 2/27/99  Written by Donald Becker
>   http://cesdis.gsfc.nasa.gov/linux/drivers/via-rhine.html
> via-rhine.c:v1.01 2/27/99  Written by Donald Becker
>   http://cesdis.gsfc.nasa.gov/linux/drivers/via-rhine.html
> via-rhine.c:v1.01 2/27/99  Written by Donald Becker
>   http://cesdis.gsfc.nasa.gov/linux/drivers/via-rhine.html
> PnP: Calling quirk for 01:00
> PnP: Calling quirk for 01:02
> isapnp: Card 'Creative SB AWE64 PnP'
> isapnp: Card 'U.S. Robotics Inc. x2 Winmodem Voice   '
> isapnp: 2 Plug & Play cards detected total
> via-rhine.c:v1.01 2/27/99  Written by Donald Becker
>   http://cesdis.gsfc.nasa.gov/linux/drivers/via-rhine.html
> via-rhine.c:v1.01 2/27/99  Written by Donald Becker
>   http://cesdis.gsfc.nasa.gov/linux/drivers/via-rhine.html
> via-rhine.c:v1.01 2/27/99  Written by Donald Becker
>   http://cesdis.gsfc.nasa.gov/linux/drivers/via-rhine.html
> via-rhine.c:v1.01 2/27/99  Written by Donald Becker
>   http://cesdis.gsfc.nasa.gov/linux/drivers/via-rhine.html

In your dmesg there should be an eth0 entry and there isn't. Your card is not
being detected. Maybe your card isn't installed correctly. Sometimes when you
install a card it doesn't get pushed in all the way, it should snap in.
 
 
 
Top

1. D-Link DFE-530tx Rev A-1 and DFE-530tx Rev D2

Freebsd ver 4.0 and 4.3   the Rev A-1 board is recognized (pci) perfect.

the Rev D2 board is a PIA.. I did manange to foolaround with the
/usr/src/sys/pci/if_vrreg.h file and get it

to been seen but then the MAC addr comes back all zeros ??

is there anyway to get this new board to work..

I did note on the rev D the  Vendor ID = 1106  the product 1186   1300
0200

on the old one ( rev A ) the product something like  3043..

anyhelp would be great..

this took me way to long to find..

code fixes ?? any tricks ??

Regards
Terry

2. corrupt files at mirrors?

3. D-Link DFE-530TX NIC configuration

4. Newbie: PCCard Ethernet Woes

5. D-Link DFE-530TX NIC configuration issue

6. Irq controlling

7. Installing a D-Link DFE-530TX NIC into Redhat6.0

8. UID/GID mess between different UNIX flavors

9. Which driver for nic D-Link 10/100 model DFE-530TX REV-A3

10. D-link DFE-530Tx NIC installation problem

11. DFE-530TX D-Link NIC

12. D-Link 10/100 (DFE-530TX) Mbps NIC Support?

13. D-Link DFE-530TX NIC module loading issues.


All times are UTC
Board index