by Hello. I recently bought a Western Digital 7193 PCI to SCSI-II card for
my Gateway P5-90, along with a Quantum 3.2G HD. I'm trying to get Linux
to recognize it, but autoprobe fails, and I can't figure out what
command-line override to use. A DOS DEBUG run gives (reformatted):
-d c800:0
C800:0000 55 AA 23 E9 5A 66 08 77-
00 00 00 00 00 00 00 00
U.#.Zf.w........
C800:0010 00 00 00 00 00 00 00 00-
1A 00 50 43 49 52 1C 10
..........PCIR..
C800:0020 96 32 00 00 18 00 00 00-
00 01 40 00 64 00 00 80
C800:0030 00 00 0D 0A 57 65 73 74-
65 72 6E 20 44 69 67 69
....Western Digi
C800:0040 74 61 6C 20 53 43 53 49-
20 42 49 4F 53 20 52 45
tal SCSI BIOS RE
C800:0050 56 49 53 49 4F 4E 20 31-
37 30 20 0D 0A 28 43 29
VISION 170..(C)
C800:0060 20 57 65 73 74 65 72 6E-
20 44 69 67 69 74 61 6C
Western Digital
C800:0070 20 43 6F 7A 70 6F 72 61-
74 69 6F 6E 20 31 39 39
Corporation 199
-d
C800:0080 35 2E 0D 0A 41 6C 6C 20-
52 69 67 68 74 73 20 52
5...All Rights R
C800:0090 65 73 65 72 76 65 64 2E-
0D 0A 00 01 00 46 00 FF
eserved......F..
C800:00A0 01 B8 AF 00 B4 00 87 DB-
52 50 2E 8A 26 2C 0A 2E
........RP..&,..
C800:00B0 8B 16 26 0A 83 C2 1F EC-
0A C0 75 58 58 5A 2E FF
..&.......uXXZ..
C800:00C0 2E 28 0A 52 50 2E 8A 26-
4C 0A 2E 8B 16 46 0A 83
.(.RP..&L....F..
C800:00D0 C2 1F EC 0A C0 75 3D 58-
5A 2E FF 2E 48 0A 52 50
.....u=XZ...H.RP
C800:00E0 2E 8A 26 6C 0A 2E 8B 16-
66 0A 83 C2 1F EC 0A C0
..&l....f.......
C800:00F0 75 22 58 5A 2E FF 2E 68-
0A 52 50 2E 8A 26 8C 0A
u"XZ...h.RP..&..
-q
The board uses IRQ 11, and I can't find a DMA assignment.
Did I buy the wrong board? The WD7000 is supported; is
this one in the same family? Please help.
Thanks in advance.
--
Eric Robert Jablow "We'll send him cheezy programs,
Herndon, VA the worst we can find, la-la-la."