Board index Solaris

Problems using cdrecord sd to mount CD-R as CD-ROM

Problems using cdrecord sd to mount CD-R as CD-ROM

Post by Brian D. Hann » Thu, 19 Aug 1999 04:00:00



Greetings from Minnesota, USA.

I am extremely impressed with Joerg Schilling's work on the cdrecord
software!
I was able to get the software installed and working with very little
trouble.
The doc was good. The hints were good.

I can record fine, but I'm having trouble mounting the CD-ROM
afterwards.
This is a Yamaha CDR-400tX.

vold is running. I've installed the sd software and rebooted. Here's
what I
see on boot:

Aug 17 16:10:38 thor unix:  SunOS Release 5.5.1 Version
Generic_103640-03 [UNIX(R) System V Release 4.0]
...
Aug 17 16:10:51 thor unix: sd5 at esp0: target 5 lun 0
Aug 17 16:10:51 thor unix: sd5 is

Aug 17 16:10:51 thor unix: secdiv: 9 secsize: 512
Aug 17 16:10:51 thor unix:      <>

Later, when I shove in a valid CD-ROM from Sun, it looks like the vold
sees it and tries to deal with it:

Aug 17 16:13:24 thor unix: secdiv: 9 secsize: 512
Aug 17 16:13:27 thor unix: WARNING:


Aug 17 16:13:27 thor unix:      data transfer overrun: current esp
state:
Aug 17 16:13:27 thor unix: esp:         State=DATA Last State=DATA_DONE
Aug 17 16:13:27 thor unix: esp:         Latched stat=0x91<IPND,XZERO,IO>
intr=0x10<BUS> fifo 0x80
Aug 17 16:13:27 thor unix: esp:         last msg out: IDENTIFY; last msg
in: COMMAND COMPLETE
Aug 17 16:13:28 thor unix: esp:         DMA csr=0xa4240010<INTEN>
Aug 17 16:13:28 thor unix: esp:         addr=fc200228 dmacnt=0
last=fc200028 last_cnt=200
Aug 17 16:13:28 thor unix: esp:         Cmd dump for Target 5 Lun 0:
Aug 17 16:13:28 thor unix: esp:         cdblen=6, cdb=[ 0x8 0x0 0x0 0x0
0x1 0x0]
Aug 17 16:13:28 thor unix: esp:         pkt_state=0xf<XFER,CMD,SEL,ARB>
pkt_flags=0x802 pkt_statistics=0x0
Aug 17 16:13:28 thor unix: esp:         cmd_flags=0x1422 cmd_timeout=60
Aug 17 16:13:28 thor unix: WARNING:

(sd0):
Aug 17 16:13:28 thor unix:      SCSI transport failed: reason 'reset':
Aug 17 16:13:28 thor unix: retrying command
Aug 17 16:13:32 thor unix: WARNING:

(sd5):
Aug 17 16:13:32 thor unix:      logical unit not ready
...(it tries twice)...

And then in the /var/adm/vold.log:

Tue Aug 17 16:13:51 1999 warning: cdrom_read: can't read the cdrom (No
such device or address)

So, is there something I'm doing wrong? Has anyone seen this before? I
looked
in the doc on the website and on dejanews, but I didn't see anything.
Any
help is GREATLY appreciated!

Thanks again for the great software,

Brian Hanna

 
 
 
Top

Problems using cdrecord sd to mount CD-R as CD-ROM

Post by Joerg Schilli » Thu, 19 Aug 1999 04:00:00


Upgrade to Solaris 2.6 or later or switch the drive to 512 bytes/sector.



>Greetings from Minnesota, USA.

>I am extremely impressed with Joerg Schilling's work on the cdrecord
>software!
>I was able to get the software installed and working with very little
>trouble.
>The doc was good. The hints were good.

>I can record fine, but I'm having trouble mounting the CD-ROM
>afterwards.
>This is a Yamaha CDR-400tX.

>vold is running. I've installed the sd software and rebooted. Here's
>what I
>see on boot:

>Aug 17 16:10:38 thor unix:  SunOS Release 5.5.1 Version
>Generic_103640-03 [UNIX(R) System V Release 4.0]
>...
>Aug 17 16:10:51 thor unix: sd5 at esp0: target 5 lun 0
>Aug 17 16:10:51 thor unix: sd5 is

>Aug 17 16:10:51 thor unix: secdiv: 9 secsize: 512
>Aug 17 16:10:51 thor unix:      <>

>Later, when I shove in a valid CD-ROM from Sun, it looks like the vold
>sees it and tries to deal with it:

>Aug 17 16:13:24 thor unix: secdiv: 9 secsize: 512
>Aug 17 16:13:27 thor unix: WARNING:


>Aug 17 16:13:27 thor unix:      data transfer overrun: current esp
>state:
>Aug 17 16:13:27 thor unix: esp:         State=DATA Last State=DATA_DONE
>Aug 17 16:13:27 thor unix: esp:         Latched stat=0x91<IPND,XZERO,IO>
>intr=0x10<BUS> fifo 0x80
>Aug 17 16:13:27 thor unix: esp:         last msg out: IDENTIFY; last msg
>in: COMMAND COMPLETE
>Aug 17 16:13:28 thor unix: esp:         DMA csr=0xa4240010<INTEN>
>Aug 17 16:13:28 thor unix: esp:         addr=fc200228 dmacnt=0
>last=fc200028 last_cnt=200
>Aug 17 16:13:28 thor unix: esp:         Cmd dump for Target 5 Lun 0:
>Aug 17 16:13:28 thor unix: esp:         cdblen=6, cdb=[ 0x8 0x0 0x0 0x0
>0x1 0x0]
>Aug 17 16:13:28 thor unix: esp:         pkt_state=0xf<XFER,CMD,SEL,ARB>
>pkt_flags=0x802 pkt_statistics=0x0
>Aug 17 16:13:28 thor unix: esp:         cmd_flags=0x1422 cmd_timeout=60
>Aug 17 16:13:28 thor unix: WARNING:

>(sd0):
>Aug 17 16:13:28 thor unix:      SCSI transport failed: reason 'reset':
>Aug 17 16:13:28 thor unix: retrying command
>Aug 17 16:13:32 thor unix: WARNING:

>(sd5):
>Aug 17 16:13:32 thor unix:      logical unit not ready
>...(it tries twice)...

--



URL:  http://www.fokus.gmd.de/usr/schilling    ftp://ftp.fokus.gmd.de/pub/unix

 
 
 
Top

Problems using cdrecord sd to mount CD-R as CD-ROM

Post by Brian D. Hann » Thu, 19 Aug 1999 04:00:00



> Upgrade to Solaris 2.6 or later or switch the drive to 512 bytes/sector.

I checked the Yamaha web page for the CD-R400 at
http://www.yamahayst.com/techsup/cdr400jm.htm It shows a single block size jumper
available, either ON or OFF. It calls this the "Select Read Block Size" and
states it must be enabled for any Unix based system. So not exactly 512
bytes/sector,  but what the heck, I tried it. It worked! Now I can write and read
CD-ROMs.

Thanks!

--
Brian Hanna
Unix Systems Admin


 
 
 
Top

Problems using cdrecord sd to mount CD-R as CD-ROM

Post by Courtney Thoma » Fri, 20 Aug 1999 04:00:00



> Greetings from Minnesota, USA.

> I am extremely impressed with Joerg Schilling's work on the cdrecord
> software!
> I was able to get the software installed and working with very little
> trouble.
> The doc was good. The hints were good.

> I can record fine, but I'm having trouble mounting the CD-ROM
> afterwards.
> This is a Yamaha CDR-400tX.

> vold is running. I've installed the sd software and rebooted. Here's
> what I
> see on boot:

> Aug 17 16:10:38 thor unix:  SunOS Release 5.5.1 Version
> Generic_103640-03 [UNIX(R) System V Release 4.0]
> ...
> Aug 17 16:10:51 thor unix: sd5 at esp0: target 5 lun 0
> Aug 17 16:10:51 thor unix: sd5 is

> Aug 17 16:10:51 thor unix: secdiv: 9 secsize: 512
> Aug 17 16:10:51 thor unix:      <>

> Later, when I shove in a valid CD-ROM from Sun, it looks like the vold
> sees it and tries to deal with it:

> Aug 17 16:13:24 thor unix: secdiv: 9 secsize: 512
> Aug 17 16:13:27 thor unix: WARNING:


> Aug 17 16:13:27 thor unix:      data transfer overrun: current esp
> state:
> Aug 17 16:13:27 thor unix: esp:         State=DATA Last State=DATA_DONE
> Aug 17 16:13:27 thor unix: esp:         Latched stat=0x91<IPND,XZERO,IO>
> intr=0x10<BUS> fifo 0x80
> Aug 17 16:13:27 thor unix: esp:         last msg out: IDENTIFY; last msg
> in: COMMAND COMPLETE
> Aug 17 16:13:28 thor unix: esp:         DMA csr=0xa4240010<INTEN>
> Aug 17 16:13:28 thor unix: esp:         addr=fc200228 dmacnt=0
> last=fc200028 last_cnt=200
> Aug 17 16:13:28 thor unix: esp:         Cmd dump for Target 5 Lun 0:
> Aug 17 16:13:28 thor unix: esp:         cdblen=6, cdb=[ 0x8 0x0 0x0 0x0
> 0x1 0x0]
> Aug 17 16:13:28 thor unix: esp:         pkt_state=0xf<XFER,CMD,SEL,ARB>
> pkt_flags=0x802 pkt_statistics=0x0
> Aug 17 16:13:28 thor unix: esp:         cmd_flags=0x1422 cmd_timeout=60
> Aug 17 16:13:28 thor unix: WARNING:

> (sd0):
> Aug 17 16:13:28 thor unix:      SCSI transport failed: reason 'reset':
> Aug 17 16:13:28 thor unix: retrying command
> Aug 17 16:13:32 thor unix: WARNING:

> (sd5):
> Aug 17 16:13:32 thor unix:      logical unit not ready
> ...(it tries twice)...

> And then in the /var/adm/vold.log:

> Tue Aug 17 16:13:51 1999 warning: cdrom_read: can't read the cdrom (No
> such device or address)

> So, is there something I'm doing wrong? Has anyone seen this before? I
> looked
> in the doc on the website and on dejanews, but I didn't see anything.
> Any
> help is GREATLY appreciated!

> Thanks again for the great software,

> Brian Hanna


Greetings,

I assume you are running Sparc. I am x86 and cannot find a binary of
cdrecord nor compile it.

Trying to compile 1.6.1.........

        make

I get...........................

        /usr/ucb/cc: language optional software package not installed
        command failed for target 'OBJ/i386-sunos5-cc/fgetline.o

If you did compile cdrecord successfully, I'd appreciate hearing about
it, and hopefully a response to what my difficulty entails.

Cordially,

Courtney

 
 
 
Top

Problems using cdrecord sd to mount CD-R as CD-ROM

Post by Sheldon T. Ha » Fri, 20 Aug 1999 04:00:00


On Thu, 19 Aug 1999 13:39:29 -0400, Courtney Thomas

Quote:>Trying to compile 1.6.1.........

>    make

>I get...........................

>    /usr/ucb/cc: language optional software package not installed
>    command failed for target 'OBJ/i386-sunos5-cc/fgetline.o

You don't have a C compiler.

Recent versions of Solaris don't come with a C compiler; get the GNU C
compiler from www.sunfreeware.com.

-Shel

--
 Sheldon T. Hall

 Looking for a newsfeed....

 
 
 
Top

Problems using cdrecord sd to mount CD-R as CD-ROM

Post by Thomas Tornblo » Fri, 20 Aug 1999 04:00:00


Is the drive set to use 512 byte blocks? These are the messages you
get when using a CDROM with 2k block size.

I know nothing of the Yamaha, but the Plextor CD-R:s we use have a
switch/strap that changes the block size from 2k to 512b.

--


Sun Microsystems AB      Fax: +46 8 623 9102

 
 
 
Top

1. CD-ROM mount needs source <--> source needs CD-ROM mount

I've just ploughed through the entirety of misc,hardware and setup, to no
avail;  I installed Linux from the sbpcd boot disk (as I have a Panasonic
CD-ROM drive hanging off a SoundBlaster-compat. card), and the CD-ROM drive
chugged away happily to give me the OS.  However, my concerns about the size of
everything I was prompted to install made me decide NOT to install the linux
source.  

Now, when I boot up the CD drive cannot be mounted because of 'wrong fs, blah
blah, or other error'.  I interrogated sbpcd.h (I *did* install the includes)
and the setup was incorrect.  Because I can't mount the CD drive I can't get
the source off the CD - re-booting off the boot disk (sbpcd) and trying a
reinstall  from the CD using setup gives a warning that the CD drive can't be
mounted.

Should I delete the linux partition and start from scratch again?  I do really
need to access the CD drive, and I realise now that it is kind of useful to
have the OS source.

Apart from that, it's great having a proper OS on my PC at last!

John

2. problem with pci=biosirq

3. replace cd-rom with CD-R / can't find mount CD-R drive

4. "Tx timed out! Resetting card" with PCMCIA WLAN card in desktop machine

5. PAS 16 CD-ROM and Slakware96, mounting CD-ROM crashes system

6. Copy playstation's CD with Linux

7. Mount CD-ROM over network and report as CD-ROM

8. How to make "xterm -C" work?

9. Mounting CD ROM vs. Mounting CD ROM

10. Linux from Nascent CD-ROM won't mount my panasonic cd-rom drive

11. CD to CD copying using cdrecord- trashed two CD's

12. cdrecord thinks CD-writer is CD-ROM

13. Cd-writer & Cd-rom not regconized in 32bitmode on Sun Ultra5, running cdrecord, fbk, scg


All times are UTC
Board index