Driver for EtherExpress(TM) PRO/100

Driver for EtherExpress(TM) PRO/100

Post by Jarrett Coffm » Sat, 07 Sep 1996 04:00:00



Does anyone know of a driver for this? Will the EtherExpress PRO driver
in the kernel handle this card too?

Thanx

 
 
 

Driver for EtherExpress(TM) PRO/100

Post by Ted Panos Ralli » Sat, 07 Sep 1996 04:00:00


There is one in modules-2.0.0.  It comes with the newest slackware
distribution.  I, unfortunately, have on EtherExpress Pro/100B, which
requires a different driver.  Does anyone know where I can get one?

Ted.


> Does anyone know of a driver for this? Will the EtherExpress PRO driver
> in the kernel handle this card too?

> Thanx

--
****************************************************************

Oracle/DEC/Sun/SGI Licence Administrator
Information Resources; 1282 Academic Surge        (916) 754-6133
UCD, Davis, CA  95616-8765                    Fax (916) 752-9017

 
 
 

Driver for EtherExpress(TM) PRO/100

Post by Donald Beck » Sat, 07 Sep 1996 04:00:00




>Does anyone know of a driver for this? Will the EtherExpress PRO driver
>in the kernel handle this card too?

The Intel EtherExpress Pro 100B driver information is on
        http://cesdis.gsfc.nasa.gov/linux/drivers/eepro100.html

Note that this driver supports only the 100B card, not the older 100A card.
The driver is still in beta test, and won't be added into the 2.0 kernel
releases.

--

USRA-CESDIS, Center of Excellence in Space Data and Information Sciences.
Code 930.5, Goddard Space Flight Center,  Greenbelt, MD.  20771
301-286-0882         http://cesdis.gsfc.nasa.gov/pub/people/becker/whoiam.html

 
 
 

1. Intel EtherExpress(TM) PRO/100

Hi,

Does anyone know which driver I should be using for my PCMCIA NIC?
The light on the card comes on briefly during startup, then when 'Starting
Network'
appears on the screen the light goes off again.  After that I get a 'device
timeout'
whenever I try to use it. This card worked fine on WinXP just a few hours
ago.

I'm new to OpenBSD (I want to try it out as we are putting in a OpenBSD
firewall
next week) but I know linux fairly well.  Is it worth recompiling the kernel
(bearing in
mind I will have to copy the source onto the laptop using floppies ;-) - if
so
what should I start with?

A section of my dmesg is below.  I thought it should use the fxp driver?

xe0 at pcmcia1 function 0 "Intel, EtherExpress(TM) PRO/100 PC Card Mobile
Adapter16, PRO/100 M16A" port 0xa000/16: address 00:a0:c9:ba:81:1b
ukphy0 at xe0 phy 0: Generic IEEE 802.3u media interface
ukphy0: OUI 0x00057d, model 0x0000, rev. 0
ukphy1 at xe0 phy 16: Generic IEEE 802.3u media interface
ukphy1: OUI 0x00057d, model 0x0000, rev. 0
ifmedia_match: multiple match for 0x20/0xfffffff

Thanks a lot,

Tom

2. Posix Threads on AIX3

3. Intel Etherexpress Pro 100 NOT 100B driver?

4. Deleting directories

5. A driver for the Intel EtherExpress PRO/100 card?

6. Trident tgui9440agi woes

7. intel etherexpress pro/100 drivers?

8. Questions

9. INTEL EtherExpress Pro/100 Drivers available?

10. Intel EtherExpress Pro 100 EISA driver?

11. Driver for EtherExpress Pro/100?

12. Intel EtherExpress PRO/100 LAN+Modem56 PC Card driver for Linux?

13. EtherExpress PRO 100 driver: can anyone assist?