ethernet card pcmcia on sony vaio with mandrake 7.1

ethernet card pcmcia on sony vaio with mandrake 7.1

Post by antoine bonamou » Thu, 04 Jan 2001 00:38:26



Hi,

I had a mistake with my pcmcia card.
This card is present on the liste of the supported cards ( d-link
DFE-650 )
Cables are ok ( it run under windows )
Pcmcia module find the card with an irq=3 ( idem windows )
But i can't ping any machine of my lan !
Dmesg :
eth0: lost link beat
eth0: Tx timed out, cable problem? TSR=0x42, ISR=0x0, t=935.

Is anybody knows what appened to my computer ?

Thanks about !

IFCONFIG :

eth0      Lien encap:Ethernet  HWaddr 00:50:BA:78:47:13
          inet adr:192.168.0.10  Bcast:192.168.0.255
Masque:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          Paquets Re?us:0 erreurs:0 jets:0 dbordements:0 trames:0
          Paquets transmis:0 erreurs:11 jets:0 dbordements:0 carrier:0

          collisions:0 lg file transmission:100
          Interruption:3 Adresse de base:0x300

lo        Lien encap:Boucle locale
          inet adr:127.0.0.1  Masque:255.0.0.0
          UP LOOPBACK RUNNING  MTU:3924  Metric:1
          Paquets Re?us:21 erreurs:0 jets:0 dbordements:0 trames:0
          Paquets transmis:21 erreurs:0 jets:0 dbordements:0 carrier:0

          collisions:0 lg file transmission:0

ROUTE :

Table de routage IP du noyau
Destination     Passerelle      Genmask         Indic Metric Ref    Use
Iface
mamachine     *               255.255.255.255 UH    0      0        0
eth0
192.168.0.0     *               255.255.255.0   U     0      0        0
eth0
127.0.0.0         *               255.0.0.0       U     0      0
0 lo
default         192.168.0.1     0.0.0.0         UG    0      0        0
eth0

INTER :

 0:     515520          XT-PIC  timer
  1:       2152          XT-PIC  keyboard
  2:          0          XT-PIC  cascade
  3:          0          XT-PIC  pcnet_cs
  8:          1          XT-PIC  rtc
 12:        151          XT-PIC  PS/2 Mouse
 13:          1          XT-PIC  fpu
 14:       4303          XT-PIC  ide0
 15:          2          XT-PIC  ide1
NMI:          0

DMESG :

Linux PCMCIA Card Services 3.1.14
  kernel build: 2.2.15-4mdk #1 Wed May 10 15:31:30 CEST 2000
  options:  [pci] [cardbus] [apm]
PCI routing table version 1.0 at 0xfdf40
  00:0c.0 -> irq 9
Intel PCIC probe:
  Ricoh RL5C478 rev 80 PCI-to-CardBus at slot 00:0c, mem 0x68000000
    host opts [0]: [isa irq] [io 3/6/1] [mem 3/6/1] [pci irq 9] [lat
168/176] [bus 32/34]
    host opts [1]: [isa irq] [io 3/6/1] [mem 3/6/1] [pci irq 9] [lat
168/176] [bus 35/37]
    PCI irq 9 test failed
    ISA irqs (default) = 3,4,5,7,10,11,12 polling interval = 1000 ms
cs: IO port probe 0x0c00-0x0cff: excluding 0xcf8-0xcff
cs: IO port probe 0x0800-0x08ff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x220-0x22f 0x330-0x337
0x378-0x37f 0x388-0x38f 0x398-0x39f 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
cs: memory probe 0xa0000000-0xa0ffffff: clean.
eth0: NE2000 Compatible: io 0x300, irq 3, hw_addr 00:50:BA:78:47:13
...
eth0: Tx timed out, cable problem? TSR=0x42, ISR=0x0, t=690.
eth0: found link beat
eth0: trigger_send() called with the transmitter busy.
eth0: lost link beat
eth0: Tx timed out, cable problem? TSR=0x42, ISR=0x0, t=990.
eth0: Tx timed out, cable problem? TSR=0x42, ISR=0x0, t=2500.
eth0: Tx timed out, cable problem? TSR=0x42, ISR=0x0, t=1500.
eth0: found link beat
eth0: lost link beat
eth0: trigger_send() called with the transmitter busy.
eth0: Tx timed out, cable problem? TSR=0x42, ISR=0x0, t=736.
eth0: found link beat
eth0: trigger_send() called with the transmitter busy.
eth0: lost link beat
eth0: Tx timed out, cable problem? TSR=0x42, ISR=0x0, t=935.
eth0: Tx timed out, cable problem? TSR=0x42, ISR=0x0, t=390000.
eth0: found link beat
eth0: lost link beat
eth0: trigger_send() called with the transmitter busy.
eth0: Tx timed out, cable problem? TSR=0x42, ISR=0x0, t=823.

 
 
 

1. Mandrake 7.1 on a Sony Vaio N505X

Hi All

I'm having problems upgrading from Mandrake 7.0 to 7.1. My Vaio (a
N505X) has a PCMCIA CD-ROM which has, in the past, worked fine provided
that linux is told where to find it, using

linux ide2=0x180,0x386

(This is how I installed Mandrake 7.0 and RedHat 6.x before it). The
Mandrake 7.1 installer suggests that you need expert mode to pass these
parameters. Fine, except I can't get it to work. Whatever I've tried, on
the initial boot up only ide0 and ide1 are detected, and the installer
then asks what driver to use (SCSI or a miscellaneous selection of other
CD-ROM's like the old SB drives, none of which apply). My CD is on ide2,
which hasn't been found anyway, so I can go no further.

Anybody know how I get the installer to detect ide2?

Cheers,

Ben.

2. TAR not working

3. Sony Vaio USB & Mandrake 7.1 incompatible

4. Solaris 2.4/ lockd errors

5. linksys pcmcia ethernet & Mandrake 7.1

6. Voice over IP

7. RedHat 7.1 install on a Sony Vaio PCG-C1XS Picturebook

8. 2.5.4[4,5] compile fix of net/rxrpc/main.c

9. Netgear FA411 ethernet pcmcia card won't run in RH 7.1

10. problems with Mandrake Linux install on a sony 505F laptop - PCMCIA card install issue

11. Help! PCMCIA and Mandrake 7.1

12. pcmcia install: Failed to connect to server (Mandrake 7.1)

13. Sony Vaio PCG-818, PCMCIA not working