ATAPI CDROM Help needed: "atapi0.1: unknown phase"

ATAPI CDROM Help needed: "atapi0.1: unknown phase"

Post by Kelvin » Mon, 28 Oct 1996 03:00:00



I'm still having trouble getting my IDE CDROM to become a device that I
can mount.  Does anyone know what I need to do when I get this message on
startup?  

wdc0: unit 1 (atapi): <NEC                 CD-ROM DRIVE:282/3.04>, removable, dma, iordy
atapi0.1: unknown phase

Enclosed below this message is the rest of the "dmesg" output in case it
helps!

As far as I can tell, i have both IDE Hard Disk and CDROM on the same
controller configured correctly.  The original setup was HD on controller
0, and CDROM on controller 1.  I moved the CDROM to controller 0, and
jumpered it as a slave.  I'm assuming that the HD is a master because NT
and DOS still recognize them when I dual boot.

Should I include my kernel configuation file???
Thanks for any help!

Kelvin

dmesg output:
------------------------------------------------------------------------------

FreeBSD 2.1.5-RELEASE #0: Fri Oct 18 00:32:17  1996

CPU: 133-MHz Pentium 735\\90 or 815\\100 (Pentium-class CPU)
  Origin = "GenuineIntel"  Id = 0x52c  Stepping=12
  Features=0x1bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8>
real memory  = 33554432 (32768K bytes)
avail memory = 30547968 (29832K bytes)
pcibus_setup(1):        mode1res=0x80000000 (0x80000000), mode2res=0xff (0x0e)
pcibus_setup(2):        mode1res=0x80000000 (0x80000000)
pcibus_check:   device 0 is there (id=122d8086)
Probing for devices on PCI bus 0:
        configuration mode 1 allows 32 devices.
chip0 <Intel 82437 PCI cache memory controller> rev 2 on pci0:0
        CPU Inactivity timer:  clocks
        Peer Concurrency: disabled
        CPU-to-PCI Write Bursting: enabled
        PCI Streaming: enabled
        Bus Concurrency: enabled
        Cache: 256K pipelined-burst secondary; L1 enabled
        DRAM: no memory hole, 66 MHz refresh
        Read burst timing: x-2-2-2/x-3-3-3
        Write burst timing: x-3-3-3
        RAS-CAS delay: 3 clocks
chip1 <Intel 82371 PCI-ISA bridge> rev 2 on pci0:7:0
        I/O Recovery Timing: 8-bit 3 clocks, 16-bit 2 clocks
        Extended BIOS: disabled
        Lower BIOS: disabled
        Coprocessor IRQ13: enabled
        Mouse IRQ12: disabled
        Interrupt Routing: A: disabled, B: disabled, C: disabled, D: disabled
                MB0: disabled, MB1:
chip2 <Intel 82371 Bus-master IDE controller> rev 2 on pci0:7:1
        mapreg[20] type=1 addr=0000ffa0 size=0010.
        I/O Base Address: %#lx
        Primary IDE: enabled
        Secondary IDE: disabled
vga0 <VGA-compatible display device> rev 0 int a irq 11 on pci0:16
        mapreg[10] type=0 addr=ff000000 size=800000.
pci0: uses 8388608 bytes of memory from ff000000 upto ff7fffff.
pci0: uses 16 bytes of I/O space from ffa0 upto ffaf.
Probing for devices on the ISA bus:
sc0 at 0x60-0x6f irq 1 on motherboard
sc0: VGA color <16 virtual consoles, flags=0x0>
ed0 not found at 0x280
ed1 not found at 0x300
sio0 at 0x3f8-0x3ff irq 4 on isa
sio0: type 16550A
sio1 at 0x2f8-0x2ff irq 3 on isa
sio1: type 16550A
sio2: disabled, not probed.
sio3: disabled, not probed.
lpt0 at 0x378-0x37f irq 7 on isa
lpt0: Interrupt-driven port
lp0: TCP/IP capable interface
lpt1 not found at 0xffffffff
psm0 at 0x60-0x63 irq 12 on motherboard
fdc0 at 0x3f0-0x3f7 irq 6 drq 2 on isa
fdc0: NEC 72065B
fd0: 1.44MB 3.5in
wdc0 at 0x1f0-0x1f7 irq 14 on isa
wdc0: unit 0 (wd0): <WDC AC21000H>
wd0: 1033MB (2116800 sectors), 2100 cyls, 16 heads, 63 S/T, 512 B/S
wdc0: unit 1 (atapi): <NEC                 CD-ROM DRIVE:282/3.04>, removable, dma, iordy
atapi0.1: unknown phase
wdc1 not found at 0x170
sea0 not found
wt0 not found at 0x300
mcd0: timeout getting status
mcd0 not found at 0x300
matcdc0 not found at 0x230
scd0 not found at 0x230
1 3C5x9 board(s) on ISA found at 0x300
ep0 at 0x300-0x30f irq 10 on isa
ep0: utp[*UTP*] address 00:c0:4f:d7:4f:77
lnc0 not found at 0x280
npx0 on motherboard
npx0: INT 16 interface
sb0 at 0x220 irq 7 drq 1 on isa
sb0: <SoundBlaster 16 4.13>
sbmidi0 not found at 0x330
Device configuration finished.
Considering FFS root f/s.
Configuring root and swap devs.
configure() finished.
BIOS Geometries:
 0:020b3f3f 0..523=524 cylinders, 0..63=64 heads, 1..63=63 sectors
 1:01300311 0..304=305 cylinders, 0..3=4 heads, 1..17=17 sectors
 0 accounted for
wd0s1: type 0x6, start 63, end = 822527, size 822465 : OK
wd0s2: type 0xa5, start 822528, end = 2048255, size 1225728 : OK
wd0s3: type 0xa5, start 2048256, end = 2116799, size 68544 : OK
fd0c: hard error writing fsbn 4 of 4-6 (ST0 40<abnrml> ST1 2<write_protect> ST2 0 cyl 0 hd 0 sec 5)
fd0c: hard error writing fsbn 13 of 13-15 (ST0 40<abnrml> ST1 2<write_protect> ST2 0 cyl 0 hd 0 sec 14)
fd0c: hard error writing fsbn 1531 (ST0 40<abnrml> ST1 2<write_protect> ST2 0 cyl 42 hd 1 sec 2)

 
 
 

ATAPI CDROM Help needed: "atapi0.1: unknown phase"

Post by Linas Vepsta » Thu, 31 Oct 1996 04:00:00



> I'm still having trouble getting my IDE CDROM to become a device that I
> can mount.  Does anyone know what I need to do when I get this message on
> startup?

> wdc0: unit 1 (atapi): <NEC                 CD-ROM DRIVE:282/3.04>, removable, dma, iordy
> atapi0.1: unknown phase

> Enclosed below this message is the rest of the "dmesg" output in case it
> helps!

> As far as I can tell, i have both IDE Hard Disk and CDROM on the same
> controller configured correctly.  The original setup was HD on controller
> 0, and CDROM on controller 1.  I moved the CDROM to controller 0, and
> jumpered it as a slave.  I'm assuming that the HD is a master because NT
> and DOS still recognize them when I dual boot.

Umm, this may be a long shot, but ... some (all?) hard drives also
have a jumper whih you have to play with.  My hard drive had three
jumper settings:

master-and-no-slave=present,
master-and-theres-a-slave,
I-am-a-slave.

You of course need to set the jumper on the hard drive for the second
one.

--linas