2511 Boot Problem

2511 Boot Problem

Post by Stephen Eli » Sun, 05 Apr 1998 04:00:00



Hello,

I having problems booting a 2511 router :

It just sits at the [2500 processor with 2048 Kbytes of main memory],
line.

Given the following output, does anyone have any ideas, thanks

(note I turned diags mode on)

====================================================

System Bootstrap, Version 5.2(8a), RELEASE SOFTWARE
Copyright (c) 1986-1995 by cisco Systems
Exiting boot state - setting bus error vector...[OK]
Sizing RAM and ROM...16 bit wide EPROM...8 Mbit EPROMs...32 bit wide
CPU RAM...Found 4 MB CPU RAM...[OK]
Testing low memory...0's...1's...address+1...[OK]
Sizing memory...writing...reading...4096 pages...memsize() returned
0x00400000[OK]
Setting cookie...[OK]
Setting memory to all ones...[OK]
Setting up exception vectors...[OK]
Enabling processor caches...set CACR to 0x2101...[OK]
Processor type is: 2500[OK]
Enabling timers...[OK]
Enabling Watchdog timer...[OK]
Sizing NVRAM...found 32K bytes of NVRAM[OK]
Searching for system code...found at 1020000, magic number =
4E56...[OK]
Setting up monitor variables...
found 2048 total Kbytes of DRAM, iomem_base set to 200000[OK]
Reading hardware revision register...
2500 processor, hardware revision = 12

Parity Logic tests...[OK]
Exiting to monitor command level

2500 processor with 2048 Kbytes of main memory

======== I hit the break key here =============

Abort at 0x10EA83E (PC)

Quote:>o

Configuration register = 0xFFFFA102 at last boot
Bit#    Configuration register option settings:
15      Diagnostic mode enabled
14      IP broadcasts do not have network numbers
13      Boot default ROM software if network boot fails
12-11   Console speed is 9600 baud
10      IP broadcasts with ones
08      Break disabled
07      OEM disabled
06      Ignore configuration disabled
03-00   Boot file is cisco2-2500 (or 'boot system' command)
 
 
 

2511 Boot Problem

Post by Stephen Eli » Sun, 05 Apr 1998 04:00:00


I've added more memory, and changed the register to 0xFFFF2101, now I
get this far and it stops. Any ideas Thanks

====================================

?
System Bootstrap, Version 5.2(8a), RELEASE SOFTWARE
Copyright (c) 1986-1995 by cisco Systems
Exiting boot state - setting bus error vector...[OK]
Sizing RAM and ROM...16 bit wide EPROM...8 Mbit EPROMs...32 bit wide
CPU RAM...Found 16 MB CPU RAM...[OK]
Testing low memory...0's...1's...address+1...[OK]
Sizing memory...writing...reading...at 0x1000840, expected 0x4000, got
0x2E003332 16384 pages...memsize() returned 0x01000000[OK]
Setting cookie...[OK]
Setting memory to all ones...[OK]
Setting up exception vectors...[OK]
Enabling processor caches...set CACR to 0x2101...[OK]
Processor type is: 2500[OK]
Enabling timers...[OK]
Enabling Watchdog timer...[OK]
Sizing NVRAM...found 32K bytes of NVRAM[OK]
Searching for system code...found at 1020000, magic number =
4E56...[OK]
Setting up monitor variables...No 2MB soldered-on...16MB only...
found 14336 total Kbytes of DRAM, iomem_base set to E00000[OK]
Reading hardware revision register...
2500 processor, hardware revision = 12

Parity Logic tests...[OK]
Exiting to monitor command level

2500 processor with 14336 Kbytes of main memory

              Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706

Cisco Internetwork Operating System Software
IOS (tm) 3000 Bootstrap Software (IGS-RXBOOT), Version 10.2(8a),
RELEASE SOFTWARE (fc1)
Copyright (c) 1986-1995 by cisco Systems, Inc.
Compiled Tue 24-Oct-95 15:46 by mkamson
Image text-base: 0x01020000, data-base: 0x00001000

====================================



Quote:>Hello,

>I having problems booting a 2511 router :

>It just sits at the [2500 processor with 2048 Kbytes of main memory],
>line.

>Given the following output, does anyone have any ideas, thanks

>(note I turned diags mode on)

>====================================================

>System Bootstrap, Version 5.2(8a), RELEASE SOFTWARE
>Copyright (c) 1986-1995 by cisco Systems
>Exiting boot state - setting bus error vector...[OK]
>Sizing RAM and ROM...16 bit wide EPROM...8 Mbit EPROMs...32 bit wide
>CPU RAM...Found 4 MB CPU RAM...[OK]
>Testing low memory...0's...1's...address+1...[OK]
>Sizing memory...writing...reading...4096 pages...memsize() returned
>0x00400000[OK]
>Setting cookie...[OK]
>Setting memory to all ones...[OK]
>Setting up exception vectors...[OK]
>Enabling processor caches...set CACR to 0x2101...[OK]
>Processor type is: 2500[OK]
>Enabling timers...[OK]
>Enabling Watchdog timer...[OK]
>Sizing NVRAM...found 32K bytes of NVRAM[OK]
>Searching for system code...found at 1020000, magic number =
>4E56...[OK]
>Setting up monitor variables...
>found 2048 total Kbytes of DRAM, iomem_base set to 200000[OK]
>Reading hardware revision register...
>2500 processor, hardware revision = 12

>Parity Logic tests...[OK]
>Exiting to monitor command level

>2500 processor with 2048 Kbytes of main memory

>======== I hit the break key here =============

>Abort at 0x10EA83E (PC)
>>o
>Configuration register = 0xFFFFA102 at last boot
>Bit#        Configuration register option settings:
>15  Diagnostic mode enabled
>14  IP broadcasts do not have network numbers
>13  Boot default ROM software if network boot fails
>12-11       Console speed is 9600 baud
>10  IP broadcasts with ones
>08  Break disabled
>07  OEM disabled
>06  Ignore configuration disabled
>03-00       Boot file is cisco2-2500 (or 'boot system' command)


 
 
 

1. Cisco 2511 boot problem

Hello !

I have a Cisco 2511 which doesn't boot, when it boot
then this is what comes on my terminal :

System Bootstrap, Version 5.2(8a), RELEASE SOFTWARE
Copyright (c) 1986-1995 by cisco Systems
2500 processor with 2048 Kbytes of main memory
Local Timeout (control reg=0x118) Error, address: 0x2132008 at 0x10FF5FE (PC)

Can anybody give me a hint ?

Regards

Roar Pettersen
Betech Data A/S
Norway


2. Export to EPS in LT

3. Boot problems in 2511

4. ??: "Never To Be Fixed" Y2K Applications

5. Cisco 2511 Not booting?

6. mode for reading news

7. Error messages on booting router 2511

8. Ricoh MP6200 User Page

9. 2511 Boot Error's

10. 2511 bootstrap boot probs

11. Help needed with 2511 booting