How to update IOS from 12.0.5 to 12.0.7 on Cisco 803

How to update IOS from 12.0.5 to 12.0.7 on Cisco 803

Post by Steve Swif » Tue, 18 Jul 2000 04:00:00



Can anyone help with this I have TFTP the new image into flash -

How do I make the 800 boot from the new image? It always loads the
12.0.5 on startup.

Router#sh flash
Directory of flash:/

  0  ----       49096   Aug 02 1999 23:22:22  TinyROM-1.2(2)
  1  -r-x     2662040   Jul 23 1999 09:19:01  [c800-y6-mw.120-5.T]
 42  -r-x     2759760   Dec 06 1999 22:05:27  c800-y6-mw.120-7.T

8388608 bytes total (2752512 bytes free)
Router#

Thanks,
Steve Swift.

 
 
 

How to update IOS from 12.0.5 to 12.0.7 on Cisco 803

Post by Fergi » Tue, 18 Jul 2000 04:00:00


Add the following to your config ....

boot system flash c800-y6-mw.120-7.T

When you are happy with the new IOS, you can then delete the 12.0.5 IOS.


Can anyone help with this I have TFTP the new image into flash -

How do I make the 800 boot from the new image? It always loads the
12.0.5 on startup.

Router#sh flash
Directory of flash:/

  0  ----       49096   Aug 02 1999 23:22:22  TinyROM-1.2(2)
  1  -r-x     2662040   Jul 23 1999 09:19:01  [c800-y6-mw.120-5.T]
 42  -r-x     2759760   Dec 06 1999 22:05:27  c800-y6-mw.120-7.T

8388608 bytes total (2752512 bytes free)
Router#

Thanks,
Steve Swift.

 
 
 

How to update IOS from 12.0.5 to 12.0.7 on Cisco 803

Post by Gerd » Tue, 18 Jul 2000 04:00:00



> Add the following to your config ....

> boot system flash c800-y6-mw.120-7.T

This command does not work on Cisco 800.

> When you are happy with the new IOS, you can then delete the 12.0.5 IOS.



> Can anyone help with this I have TFTP the new image into flash -

> How do I make the 800 boot from the new image? It always loads the
> 12.0.5 on startup.

> Router#sh flash
> Directory of flash:/

>   0  ----       49096   Aug 02 1999 23:22:22  TinyROM-1.2(2)
>   1  -r-x     2662040   Jul 23 1999 09:19:01  [c800-y6-mw.120-5.T]
>  42  -r-x     2759760   Dec 06 1999 22:05:27  c800-y6-mw.120-7.T

> 8388608 bytes total (2752512 bytes free)
> Router#

> Thanks,
> Steve Swift.

Perform the following steps:

reboot the router and press Control-C to enter ROM-Monitor
The router promts    ->  boot#
type:   set file-name="c800-y6-mw.120-7.T" to change name of the
boot-image.
type: save       to save changes.
type: boot        to boot the router with the new image.

See also Cisco 800 Series Router Software Configuration Guide,Appendix D

Good luck
Gerd

 
 
 

How to update IOS from 12.0.5 to 12.0.7 on Cisco 803

Post by Fergi » Thu, 20 Jul 2000 04:00:00


As you can see, my TinyROM version is only 1.0(2) and it works on my
router....

Cisco Internetwork Operating System Software
IOS (tm) C800 Software (C800-SY6-MW), Version 12.1(1), RELEASE SOFTWARE
(fc1)
Copyright (c) 1986-2000 by cisco Systems, Inc.
Compiled Tue 14-Mar-00 17:24 by cmong
Image text-base: 0x000EA000, data-base: 0x006D9000

ROM: TinyROM version 1.0(2)
Router uptime is 5 weeks, 21 hours, 22 minutes
System returned to ROM by power-on
System restarted at 14:06:27 AEST Tue Jun 13 2000
System image file is "flash:c800-sy6-mw.121-1.bin"

Cisco C803 (MPC850) processor (revision 1) with 47896K bytes of virtual
memory.
Processor board ID JAD03265118
CPU part number 33
X.25 software, Version 3.0.0.
Bridging software.
Basic Rate ISDN software, Version 1.1.
2 POTS Ports
1 Ethernet/IEEE 802.3 interface(s)
1 ISDN Basic Rate interface(s)
8M bytes of physical memory (DRAM)
8K bytes of non-volatile configuration memory
8M bytes of flash on board (4M from flash card)

Configuration register is 0x2102





>> Add the following to your config ....

>> boot system flash c800-y6-mw.120-7.T

>This command does not work on Cisco 800.

It does if you have the latest TinyROM, 1.2(2), as this person does.
There is a bug in all previous versions.  Just used this command
myself to activate an upgrade of my own image.  The old fashioned way
you mention still of course works.  Also, to fully get rid of the
previous image (after booting the new one), use 'squeeze flash:'.
>> When you are happy with the new IOS, you can then delete the 12.0.5 IOS.



>> Can anyone help with this I have TFTP the new image into flash -

>> How do I make the 800 boot from the new image? It always loads the
>> 12.0.5 on startup.

>> Router#sh flash
>> Directory of flash:/

>>   0  ----       49096   Aug 02 1999 23:22:22  TinyROM-1.2(2)
>>   1  -r-x     2662040   Jul 23 1999 09:19:01  [c800-y6-mw.120-5.T]
>>  42  -r-x     2759760   Dec 06 1999 22:05:27  c800-y6-mw.120-7.T

>> 8388608 bytes total (2752512 bytes free)
>> Router#

>> Thanks,
>> Steve Swift.

>Perform the following steps:

>reboot the router and press Control-C to enter ROM-Monitor
>The router promts    ->  boot#
>type:   set file-name="c800-y6-mw.120-7.T" to change name of the
>boot-image.
>type: save       to save changes.
>type: boot        to boot the router with the new image.

>See also Cisco 800 Series Router Software Configuration Guide,Appendix D

>Good luck
>Gerd

 
 
 

How to update IOS from 12.0.5 to 12.0.7 on Cisco 803

Post by Steve swif » Fri, 21 Jul 2000 04:00:00


Thanks guys, all these methods worked, but your information did not
reach my news server quick enough.

This was what I eventually did :-

enable
sh ver and made note of control reg (0x2102)
conf t
config-reg 0x2101
end
write  mem
reload
enable
copy tftp flash
192.168.x.x
new image file name
now new flash is made default boot

do not reload yet

conf t
config-reg 0x2102
end
write mem
reload

This seemed to work ok, I then erased the old image